User manual NEFF S41M50N0GB

[. . . ] 9000 405 166 (8906) en Operating instructions n 7 8 9 10 Reset 3 sec. Start ABC 1 2 3 4 5 6 20 21 22 23 24 25 26 27 28 29 30 31 32 en Table of contents Washing the dishes . 16 16 16 16 16 16 16 16 17 17 17 17 18 18 18 18 19 19 20 20 20 20 21 21 22 23 23 23 23 24 24 24 24 24 25 25 25 25 25 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] You can change your programme selection at any time until the programme starts. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. If the Aqua sensor is active, "clean" rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3­6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. End of programme The programme has ended when the value : is indicated on the numerical display )". Switching off the appliance Short time after the end of the programme: ­ Switch off ON/OFF switch (. ­ Remove the utensils when they have cooled down. Switching on the appliance ­ Turn on the tap fully. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display )". The programme starts running. ã=Warning Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display )". The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. 16 en Interrupting the programme ­ Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. ­ To continue the programme, switch on the ON/OFF switch ( again. Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Hold down programme button # and press START button P until the digital display )" : . . . The LED for button # flashes and the digital display )" displays the factory setting : . ­ Press programme button # until the factory set value : is indicated on the digital display )". To change the setting, ­ Press the button 3 to switch the Intensive drying on : or off : . The set value is saved. Terminating the programme (Reset) ­ Press START button P for approx. ­ Switch off ON/OFF switch (. Changing the programme When the START button P has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). 17 en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. The filter system consists of a coarse filter, a flat fine filter and a microfilter. [. . . ] Drain the appliance according to the following steps: ­ Turn on the tap. The expected programme duration is indicated on the numerical display )". 4 minutes press the START button P until : is indicated on the digital display. (This prevents residual water from running into the machine control and damaging the programme sequence. ) Waste disposal Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials. [. . . ]