User manual NEFF K7791X0

[. . . ] K7791X0. . 9000 291 220 (8707) en Installation Instructions Content Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Subsurface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If it is not possible to securely fasten the anti-tilt ribs and consequently, not possible to securely fasten the appliance using the fastening screws supplied, select another suitable method for securely fastening the anti-tilt ribs. In the case of some fitted shapes, it may be necessary to screw in at an angle the wood screws used to fasten the anti-tilt ribs to the rear wall. ­ 11 Subsurface wooden floors The wood screws (5 x 60 mm and 4 x 15 mm) which are supplied should be used for wooden floors. Drilling guide holes: 3 mm for woodscrews (5 x 60 mm) 2 mm for woodscrews (4 x 15 mm) Make sure that the screws 5 x 60 grip at least 19 mm into the solid subsurface. Strike the dowel and screw into the hole until the head of the screw has a 13 mm distance to the anti-tilt securing device. Re-examine to make sure that the screws are firmly tightened. Subsurface concrete Warning!When installing or working with floor anchors always use protective glasses and other protective equipment or protective clothing ­ risk of injury!Floor anchors are not suitable for use in connection with lightweight construction masonry, breeze blocks or tiles. Drill a hole with a 10 mm diameter having a depth a little more than the raising depth. Additionally use the supplied wood screws (if the subsurface allows). 6. Attaching an additional anti-tilt mechanism Important note: As far as possible, always screw the wooden plank to the rear wall of the niche. If the anti-tilt ribs cannot be fastened securely, a wooden beam can be used above the appliance as an alternative anti-tilt mechanism. Care should be taken that there is not a gap between the appliance and the wooden beam. Note: ­ If the installation niche is deeper than the appliance, select a stronger beam or use two, one behind the other. The plank must overlap the appliance by at least 50 mm. ­ 12 7. Preparing the water connection Warning! (only for appliances which require a water connection) Turn off the main water tap in order to avoid damage from escaping water. Always keep to the given installed area in order to avoid damaging the connection pipe when sliding the appliance in later. Mark the installation height (underside edge of the plank) on the rear wall of the niche. Select the screws according to the thickness of the wooden plank: Length min. Select the number of screws corresponding to the niche width so that you ensure that the plank can be securely mounted. According to the subsurface: Look for the supports on the rear wall of the niche and mark the drill holes on the plank corresponding to the position of the support. Screw the plank onto the rear wall of the niche. Fix the connection pipe to the floor with adhesive tape. 8. Attaching the edge protectors In order to protect the edges of the installation niche, attach the supplied protection ribs with adhesive tape. 13 9. Sliding the appliance into the installation niche Note: If the floor or appliance is skew in relation to the installation niche, the height-adjustable wheels should be correspondingly adjusted before sliding the appliance into the niche. Note: A separate plug is necessary for each appliance in the case of side-by-side set up!Protect the mains lead from getting wedged under or behind the appliance. Recommended procedure: Tie a rope onto the middle of the mains lead and slide the appliance forwards. Pull the cable onto the rope when sliding the appliance into the niche. [. . . ] Re-examine the dimensions of the crack continuously. Screw the nuts on the adjusting rib tightly. Fix the furniture door (freezer compartment) Important note: Now attach the door handles which should have been screwed from behind! Attaching the fixing angles: Lift the furniture door somewhat from the appliance door. Press the upper fixing angle (without clip (1. )) on the using the screws. right and left at position Insert the fixing angle (with clip (2. )) on the right and left at position into the fixing plate and slide over the screws of the appliance door. [. . . ]