User manual NEFF D76E21N0GB

[. . . ] Installation instructions and how to use and look after your built-in cooker hoods NEFF (UK) Ltd Fig. 1 ELECTRO 2 Table of contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information on protection of the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before using the appliance for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 4 5 5 5 6 7 7 8 8 8 9 10 11 11 11 12 13 13 14 15 15 16 17 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The extractor hood must not be installed over a solid fuel heating appliance which may be a fire risk (e. g. flying sparks) unless the heating appliance has a closed, nondetachable cover and the country-specific regulations are observed. To avoid damaging the hob, cover it when installing the extractor hood. RISK OF FIRE Do not flambé under the extractor hood or work with a naked flame. Do not leave pans, frying pans or deep-fat fryers unattended if you are cooking food with oils or fats, e. g. A risk of fire can be prevented by cleaning the grease filters regularly and changing the activated-carbon filter in good time. Never operate the extractor hood without grease filters. 7 Operating modes The extractor hood can be used in exhaust air and circulating air mode. Exhaust-air mode Appliance dimensions Exhaust air min. 580 max 1. 030 The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system. min. 450 400 Circulating-air mode Appliance dimensions Circulating air min. 580 max 1. 030 The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen. An activated carbon filter must be installed to bind odours in circulating-air mode (see "Removing and installing the grease filters"). The complete installation set as well as the replacement filters are available from specialist outlets, customer service or the Online Shop. The accessory number can be found at the end of the operating instructions. min. 450 8 Operation The description of the operation applies to several appliance models. ­ Clean carefully in the area of the controls to avoid liquid from getting into the electronics. NOTE: Clean the stainless steel surfaces in the direction of the ground surface only!Do not use stainless steel cleaner for the control buttons! Cleaning the metal-mesh grease filters . . . Under normal operation (daily 1 to 2 hours), the metal-mesh grease filters must be cleaned 1x month. . . . in the dishwasher The metal-mesh grease filters can be cleaned in the dishwasher. Slight discolouration may occur but this will not affect the function of the grease filters. NOTE: Do not clean heavily saturated metalmesh grease filters together with utensils. . . . by hand When cleaning by hand, soak the grease filters in a hot detergent solution, brush off the dirt, rinse thoroughly and leave to dry. If dirt is particularly stubborn, we recommend using a special grease solvent spray. This can be ordered via the Online Shop. 10 Removing and installing the grease filters Before removing and installing the grease filters, always follow the instructions and warnings in the chapter entitled "Safety instructions"! [. . . ] Attach the earthed socket as directly as possible behind the flue duct. ­ If the earthed socket is no longer accessible following installation of the extractor hood, a disconnector must be fitted as for a permanent connection. If a permanent connection is required A disconnector must be provided on the installation side. Switches with a contact opening of more than 3 mm and all-pole disconnection are regarded as disconnectors. This includes LS switches, fuses and contactors. Electrical specifications WARNING: THIS APPLIANCE MUST BE EARTHED IMPORTANT: Fitting a Different Plug: The wires in the mains lead are coloured in accordance with the following code: Green and Yellow ­ Earth Blue ­ Neutral Brown ­ Live If you fit your own plug, the colours of these wires may not correspond with the identifying marks on the plug terminals. [. . . ]