User manual NEC XV2930

[. . . ] WARNING AND CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns he user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, if it is dangerous to make any kind of contact with any part inside of the unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. [. . . ] If you are experiencing a problem with you monitor, please contact the authorized NEC Visual Systems Division dealer from which it was purchased. If this is a reseller who is unable to provide service, call the Service Account Administrator at 800-836-0655. DOA POLICY A product is considered DOA if it fails to function according to current published specifications because of defects in NECTECH factory materials and/or workmanship during the first 30 days from the date of purchase by the end user. After the 30-day period any defective product will be considered a warranty repair. A product is NOT considered DOA is it is functional but the box is damaged or if it is missing contents such as manuals, cables, etc. ELIGIBILITY/RETURN FOR EXCHANGE PROCEDURE If a product is suspected of being DOA, customers must call NECTECH VSD Technical Assistance Center. Our representative will assist in making the product fully functional or verity it as a DOA. VSD Technical Support l-800-366-5213 NEC technical support will provide a procedure for repair. If the product is determined to be DOA, the Service Account Administrator will request the following information in order to issue a material return authorization (MRA) number: Product model number Serial number A complete description of problem If approved, an MRA number and return address will be issued. All products to be returned must be shipped freight pre-paid in its original carton to a designated NECTECH facility. The defective product must be received by NECTECH within 21 calendar days from the date the MRA was issued. Any questions concerning service and repair policies or procedures can also be addressed in writing to: NEC Technologies Visual Systems Division Customer Service & Support 1250 North Arlington Heights Road ltasca Illinois 60143 4 SPECIFICATIONS 1. Light transmission 29 inch (27 inch viewable) H=0. 74mm, V=0. 64mm 49% typical 2. Line regulation 120 Vac ~ 60Hz 2 A at 120 Vac / 60Hz 50A 240 Watts (Max) 95 to 145 Vac / 60Hz 3. Dot rate Analog Positive RGB: 0. 7 Vp=p/AV: 1 . O Vp-p 75 ohms 50MHz(max. ) Horizontal sync a. Frequency TTL positive or negative 1 K ohm (Min) RGB: 31 KHz to 38 KHz Video: 15. 734 KHz (NTSC) / 60Hz TTL positive or negative 1 K ohm (Min) 50 Hz. Pin assignments for D-type connector Pin 1: RED Pin 2: GREEN Pin 3: BLUE Pin 4: GND Pin 5: GND Pin 6: RED RETURN Pin 7: GREEN RETURN Pin 8: BLUE RETURN Pin 9: NC Pin 10: GND Pin 11: GND Pin 12: SDA Pin 13: H-SYNC Pin 14: V-SYNC Pin 15: SCL 5 6. User controls 520mm +/- 5 min (for mode 1-6) 388mm +/- 5 min (for mode 1-6) Power, Brightness, contrast, V-Size, Mute, V-position, H-Size, Tint, H-Position, Degauss, Pincushion, Rotation, Bass Treble, Balance, Color, Sharpness, Volume, Woofer, audio FIX/VAR, Recall, Input. High leakage current, earth connection essential before connecting supply. Connect the video cable (AV, S-Video or RGB cable) and audio cable to your monitor. The power indicator should be illuminated. 10 USING THE MONITOR'S FEATURES The MultiSync XV29 features advanced on screen adjustment for optimal viewing. To access the advanced features, open the access panel by pressing down on the center of the door on set or use the remote control. Press the button again, the green LED disappears and the red LED (stand by) lights up indicating that the power is OFF. The following audio functions are available only if there is audio connected to the unit. [. . . ] Select this icon to adjust the vertical position of the displayed image. Select this icon to adjust the horizontal size of the displayed image. Select this icon to adjust the horizontal position of the displayed image. Select this icon to adjust the amount of tapering on each side of the displayed image. [. . . ]