User manual NEC XT9000

[. . . ] High Light Output Projection System · Großbildschirm Projektions-System XT9000 User's Manual · Bedienungshandbuch XT9000 High Light Output Projection System User's Manual CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. Precautions: Please read this manual carefully before using your NEC XT9000 Projector and keep the manual handy for future reference. 3. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. [. . . ] See page E-9 for "Lens Shift Adjustable Range". POSI/ LENS (3) Press and hold the CTL button and press the FOCUS + or - button to obtain the best focus optically. You can also adjust the focus by using the FOCUS + or - button on the projector cabinet. CTL FOCUS + - MAGNIFY/ ZOOM + - CTL ENTER E ­ 12 Keystone 2) Hookup 2-1. Use the supplied DVI-D cable to connect the RGB DIGITAL output of the master projector to the RGB DIGITAL input (INPUT9 )of the slave projector until all the projectors are connected. Keystone distortion Normal 2-2. Next, using a commercially available, bi-directional RS-232C cable connect the OPTION OUT terminal of the master projector to the OPTION IN terminal of the slave projector until all the projectors are connected. Turn all the projectors on and roughly make some optical adjustments to each projector. 3) Adjusting and registering signals to be projected in Link mode and stack application. Create data for the master projector and copy data to the slave projector. Choose one projector as the master. Keystone is the distortion of a projected image that usually creates a wider top than bottom. Aiming a projector upward on a wall rather than straight at a wall creates this distortion. Use the or buttons on the slide bar to correct this keystone (trapezoidal) distortion. NOTE: The keystone feature is not available when the test pattern or the blue back is displayed. NOTE: With the projector aimed directly at the screen the maximum keystone angle that can be corrected is +/- 15 degrees. Setting up for Double Stacking in Link Mode 3-1-2. Display all desired input signals, make adjustment to each signal, then save all adjustments on the master projector. NOTE: DO NOT TURN OFF THE POWER while the PC Card Access indicator is flashing. Doing so will cause damage to the data of the projector system. NOTE: Back up your data if you use the supplied CompactFlash card to copy the data from the master projector to the slave projector. The supplied CompactFlash card contains data and firmware for factory use. 3-1-5-2. Press and hold CANCEL, then press POWER on the rear panel of the master projector. The POWER indicator will change to steady green and the PC Card Access indicator will start flashing. After storing data on the PC card, the POWER indicator will change to orange. Transfer the data to the slave projector using the PC card so that all the projectors have the same data in memory. Insert the PC card into the slot of a slave projector. CAUTION: To prevent the projectors from falling, install them in a place and fasten them in a way with sufficient strength to support the two projectors. NOTE: SW 1 Level and SW 2 Level of Switcher Control are not available on Link Mode. 1) Stacking the Projectors 1-1. Place the projectors at the proper height for best screen to projector relationship. [. . . ] For the wireless remote control not to operate, insert the plug of the remote cable into the REMOTE2 IN jack. E ­ 42 8. Compatible Input Signal List Compatible Input Signal List Signal Name Horizontal Freqency [kHz] Video(NTSC) 15. 734 Video(PAL/SECAM) 15. 625 Video (HDTV) 1920x1080i 33. 75 Video (HDTV) 1280x720p 45 Video (HDTV) 1920x1080i 26. 97 Video (HDTV) 1920x1080p 26. 97 Video (HDTV) 640x480p 31. 5 Video (HDTV) 1080x25p 28. 13 Video (HDTV) 1080x30p 33. 72 Video (HDTV) 1080x50i 28. 13 APPLE MAC13"@67Hz 35. 00 APPLE MAC16"@75Hz 49. 72 APPLE MAC21"@75Hz 68. 68 APPLE MAC23"@65Hz 69. 87 APPLE MAC23"@74Hz 78. 44 APPLE MAC28"@69Hz 85. 21 SGI XGA@60Hz/70MHz 49. 72 SGI SXGA@76Hz 81. 97 Sun 1152x 900@66Hz 61. 80 Sun 1152x 900@76Hz 71. 71 Sun 1024x1024@61Hz 65. 27 HP XGA@75Hz 62. 94 VESA VGA@60Hz 31. 46 VESA VGA@72Hz 37. 86 VESA VGA@75Hz 37. 50 VESA VGA@85Hz 43. 27 VESA SVGA@60Hz 37. 88 VESA SVGA@72Hz 48. 00 VESA SVGA@75Hz 46. 88 VESA SVGA@85Hz 53. 67 VESA XGA@43Hz 35. 52 VESA XGA@60Hz 48. 36 VESA XGA@70Hz 56. 48 VESA XGA@75Hz 60. 02 VESA XGA@85Hz 68. 68 VESA1152x 864@60Hz 54. 35 VESA1152x 864@70Hz 63. 99 VESA1152x 864@75Hz 67. 50 VESA1152x 864@85Hz VESA1280x 960@60Hz VESA1280x 960@75Hz VESA1280x 960@85Hz VESA SXGA@43Hz VESA SXGA@60Hz VESA SXGA@75Hz VESA SXGA@85Hz VESA UXGA@48Hz VESA UXGA@60Hz VESA UXGA@65Hz VESA UXGA@70Hz VESA UXGA@75Hz VESA UXGA@85Hz 77. 49 60. 00 75. 00 85. 94 46. 43 63. 98 79. 98 91. 15 62. 50 75. 00 81. 25 87. 50 93. 75 106. 30 Vertical Frequency [Hz] 60 50 60 60 47. 95 23. 98 60 25 30 50 66. 67 74. 55 75. 06 65. 18 73. 72 68. 66 60. 04 75. 97 65. 95 76. 05 61. 40 74. 93 59. 93 72. 81 75. 00 85. 01 60. 32 72. 19 75. 00 85. 06 86. 96 60. 00 70. 07 75. 03 85. 00 60. 05 70. 02 75. 00 85. 06 60. 00 75. 00 85. 00 86. 88 60. 02 75. 02 85. 02 96. 08 60. 00 65. 00 70. 00 75. 00 85. 00 NOTE1: The VGA, SVGA, SXGA and UXGA signals are displayed with Advanced AccuBlend. NOTE 3: DVI digital signal can support a maximum resolution of XGA@85Hz. E ­ 43 9. List of Menu Items Available on Link Mode See the table below for available functions in the digital link mode and the analog link mode. [. . . ]