User manual NEC XL3500

[. . . ] MultiSync Hivid 3500 Projector Large Screen MultiSync Projection System User's Manual Model number: XL-3500 CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. Precautions Please read this manual carefully before using your NEC MultiSync Hivid 3500 Projector and keep the manual handy for future reference. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. [. . . ] To select the next signal use the CURSOR or button and press ENTER. 31 3. OPERATION Source Information Provides and changes information for the parameters of your current projected source. NOTE: For other registered signals, change their parameters on the Source Registry menu. The menu items you can display, change or specify are as follows: Source Name --------------- Changes a user name that has previously been entered. Direct Key ------------------ Assigns settings of source to each INPUT button (1-10) with CTL. Input Slot ------------------- Selects an input terminal for the registered signal when you need to do due to adding optional equipment. Signal System -------------- Displays the signal system of the current source such as RGB, Video, SVideo, or Component signal. Sync System --------------- Selects the detection method of the sync signal. Color Matrix ---------------- Selects the mode to match the output format of an HDTV or DVD signal. CTI Control ----------------- Turns this feature on so you can make (Color Transient Improvement) the color sharper. Noise Reduction ----------- Turns this feature on so video noise can be reduced. Stadium Mode ------------- Selects this feature so the picture is expanded in the horizontal and vertical directions at different ratios. Source Select Counter ---- Resets the number of times a signal is selected for display. or button to select the item you want to Source Information (List No. 99) Source Direct Input Signal Video Sync Sync Name Key Slot System System Frequency Polarity Page1/2 [NTSC3. 58] [CTL+10 [INPUT A Key ] ] S-VIDEO NTSC3. 58 Cinema fH= fV= 15. 74KHz 61. 23Hz VD(+) HD(+) Source Information (List No. 99) Sync Sync System Termination Mode Page2/2 [Auto ] H/V Separate [Hi-Z ] ] ] Display Color CTL [00:NTSC [Y, B-Y, R-Y [OFF [OFF ] ] ] 00M Matrix Control Reduction Mode Noise Stadium [Normal 0000 0000H Select Counter Display Timer 32 3. OPERATION The following items can be set: s Source Name To change the source name or input a new source name by selecting one character at a time with the INPUT buttons 1 through 10 and by moving the cursor with the CURSOR button. Only after completely finishing the selection of the characters, press ENTER. · If you have made an error, use the CURSOR button and reenter the correct letter or number. To delete one character, move the highlight to the character to be deleted and then press the NORMAL button. To delete all the entered name, hold down the CTL button then press the NORMAL button. See To change the source name or input a new source name by selecting one character at a time with the INPUT buttons 1 through 10 and by moving the cursor with the CURSOR button. Only after completely finishing the selection of the characters, press ENTER. · If you have made an error, use the CURSOR button andreenter the correct letter or number. [. . . ] If the remote control loses power, the remote control address becomes "00". In this case the on-screen shown on the right above is not displayed on the screen. 3) To complete, press END. 73 3. OPERATION Help Menu Provides information about operation and adjustment procedures or the set information. To view the information: Press OPERATE or ADJUST button then select "Help" from the Task bar and press ENTER. [. . . ]