User manual NEC XG85RP-CH

[. . . ] MultiSync XG85RP/XG85RPW MultiSync XG135RP Large Screen MultiSync Rear Projection System Set-Up Manual Model Number: XG-852C/XG-1352C The projector must be assembled by qualified installation technicians. 2 654321 654321 654321 654321 654321 654321 654321 CONTENTS. SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Displaying the Various Setting Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Projection Type Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Connecting to the Switcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When you try to enter the ADJUST mode again, you will need to re-enter your passcode. When you try to enter the ADJUST mode again, you will not need to re-enter your passcode. 66 CRT - R 3200K 9500K ­ 1 2 3 4 5 6 7 8 9 A / / / / / / / / / DJUST ­ SIGNAL ENTRY FOCUS ALIGNMENT CONVERGENCE KELVIN R, G, B GAIN PASSCODE OPTION REF. ADJUST ­ KELVIN ­ 1 / COLOR TEMP. 2 / WHITE BAL. COLOR TEMPERATURE WHITE BALANCE WHT BLK 60% 10% R E T U R N U S E R MO D E ?YES NO ADJUSTMENT R, G, and B Gain Adjustment Adjusts the input level of the signal. NOTE: This adjustment works only with the ISS-6020/ISS-6020G Switcher. Proceed as follows: 1 Press the ADJUST button to display the "ADJUST" menu. 2 Use the CURSOR or button to highlight the "6/R, G, B GAIN" line. Press ENTER to display the "R, G, B GAIN" adjustment screen. You can also select the "R, G, B GAIN" adjustment screen directly by pressing the INPUT "6" button. ­ 1 2 3 4 5 6 7 8 9 A / / / / / / / / / DJUST ­ SIGNAL ENTRY FOCUS ALIGNMENT CONVERGENCE KELVIN R, G, B GAIN PASSCODE OPTION REF. ADJUST 3 Hold down the CTL button then select the CRT you wish to adjust with the R, G, and B buttons. NOTE: Connect the projector and the Switcher with a oscilloscope, then adjust the CURSOR buttons to obtain a value of 0. 7Vp-p of the projector input level or the Switcher output level on the oscilloscope. · Whenever the END button is pressed, the menus will sequence in this order: "ADJUST" menu Source screen · If the "RETURN USER MODE?" menu appears, use the CURSOR or button to select either "YES" or "NO" and then press ENTER. When you try to enter the ADJUST mode again, you will need to re-enter your passcode. When you try to enter the ADJUST mode again, you will not need to re-enter your passcode. R, G, B GAIN CRT - R - 60% R E T U R N U S E R MO D E?YES NO 67 654321 654321 654321 654321 654321 654321 654321 PASSCODE. Entering Passcode To prevent any unauthorized operation or mis-adjustment, the projector is equipped with a passcode option. If your passcode has not been entered correctly, the "ADJUST" and "REF. When the ADJUST button is pressed, and no passcode has been entered, the "PASSCODE?" screen is displayed. · The "PASSCODE?" screen is displayed. 2 Enter the four digit passcode you have already registered by using the "1" through "0" buttons. 1) Each time you press the INPUT button, an asterisk appears under the "PASSCODE?" message. 2) After you have finished entering the four digit passcode, press ENTER. NOTE: If you have made an error, press the NORMAL button to delete the asterisk "". To delete all the entered digits, hold down the CTL button then press the NORMAL button. [. . . ] Countermeasures: Connect a VIDEO or S-VIDEO signal to the VIDEO input board and an RGB or COMPONENT signal to the RGB input board. AN INPUT SIGNAL IS DIFFERENT FROM THE SELECTED CONTENTS IN SIGNAL ENTRY WINDOW. MASSAGE LIST The following messages are displayed at the bottom portion of the screen. Conditions TEST button is depressed at the time of the POSITION-SHIFT adjustment. R, G, B button is depressed at the time of the BRIGHT, WHITE-BAL, COLOR TEMP. , COLOR SHIFT, and BASE WHITE adjustments. [. . . ]