User manual NEC XG1352

[. . . ] 654321 654321 654321 654321 654321 654321 INTRODUCTION. Before operating this projector, please read this manual carefully and completely. This manual will provide you with the basic instructions for operation of the projector. Installation, preliminary adjustments and procedures which require the opening of the projector and contact with electrical components should be performed by service personnel. For continued safe and reliable operation, use only cables supplied by the manufacturer for power. [. . . ] YES NO 107 SETTING Auto Sequence Setting You can program the projector to change sources. To do this proceed as follows: 1 Press the ADJUST button to display the "ADJUST" menu. See page 61 for the explanation of the PASSCODE. 2 Use the CURSOR or button to highlight the "8/OPTION" line. You can also select the "OPTION" menu directly by pressing the INPUT "8" button. ­ 1 2 3 4 5 6 7 8 9 A / / / / / / / / / DJUST ­ SIGNAL ENTRY FOCUS ALIGNMENT CONVERGENCE KELVIN R, G, B GAIN PASSCODE OPTION REF. ADJUST 3 Use the CURSOR or button to highlight the "3/SEQUENCER" line. You can also select the "SEQUENCER" menu directly by pressing the INPUT "3" button. · The "SEQUENCER" screen will be displayed. ­ 1 2 3 4 5 6 7 O / / / / / / / PTION ­ SETTING MODE MENU MODE SEQUENCER PJ ADDRESS VERSION HOUR METER DEFAULT DATA 4 Use the CURSOR or button to select the "EDIT" and press ENTER. · This will bring you to the "EDIT" mode, and a program line is highlighted. Correctsorcreatestheprogramdata. OPTION P01 NO 01 02 03 04 05 06 07 08 09 10 INPUT M-10 M-02 M-01 WAIT M-01 WAIT LOOP M-02 P-OFF P-ON - SEQUENCER - S-01 S-02 S-02 S-01 TIME 12:00:00 14:00:00 00:10:00 SMTWTFS XOOOOOX XOOOOOX XOOOOOX XOOOOOX 00:20:00 03 COUNT 05 S-02 15:50:00 18:00:00 09:00:00 START EDIT XOOOOOX XOOOOOX XOOOOOX 108 SETTING 5 Use the CURSOR or button to highlight the line to be input and press ENTER. · The Program menu is displayed. OPTION P01 NO 01 02 03 04 05 06 07 08 09 10 INPUT M-10 M-02 M-01 WAIT M-01 WAIT LOOP M-02 P-OFF P-ON - SEQUENCER - S-01 S-02 S-02 S-01 TIME 12:00:00 14:00:00 00:10:00 SMTWTFS XOOOOOX XOOOOOX XOOOOOX XOOOOOX 00:20:00 03 COUNT 05 S-02 15:50:00 18:00:00 09:00:00 START EDIT XOOOOOX XOOOOOX XOOOOOX 6 Use the CURSOR or and press ENTER. button to highlight the desired item slc o e s et t tm e I · INPUT . . . . . . Selecting "INPUT" When using in stand alone application: 1) Use the CURSOR or button to select "INPUT" and press ENTER. · The "INPUT TERMINAL SELECT" terminal menu is displayed. INPUT WAIT GOTO LOOP P-ON P-OFF INSERT DELETE INPUT WAIT GOTO LOOP P-ON P-OFF INSERT DELETE 2) Use the CURSOR or button to select an input slot and press ENTER. · The "TERMINAL SELECT" menu is displayed. INPUT TERMIN INPUT INPUT INPUT AL SELECT A B C 3) Use the CURSOR or button to select either "VIDEO", "RGB", "S-VIDEO" or "COMPO. "and press ENTER. · The "TIME" input screen is displayed. VIDEO RGB S-VIDEO COMP. 4) Enter the starting time using INPUT buttons and press ENTER. · If you have made an error in the input of numbers, press the END button to return to the "VIDEO/RGB/S-VIDEO/ COMPO. " terminal menu then start from step 3). 109 TIME __:__:__ SETTING 5) Use the CURSOR or button to select any day of the week, then select either "YES" or "NO" with ENTER. · When "DAILY" selected, the entire week is changed to "YES". · When "END" is selected, the current setting is saved. NOTE: Typing99:99:99inthetimeinputmenuwillexecutethe programimmediately. (Seetheexampleinthe"WAIT"section on page 108) When using with a single ISS-6020/ISS-6020G Switcher: 1) Use the CURSOR or button to select "INPUT" and press ENTER. · The "MASTER" menu will be displayed. WEEK SELECT DAILY SUN NO MON YES TUE YES WEN YES THU YES FRI YES SAT NO END INPUT WAIT GOTO LOOP P-ON P-OFF INSERT DELETE 2) Use the CURSOR or button to select the input slot number of the Switcher and press ENTER. · The "TIME" input screen will be displayed. MASTER SLOT­0 SLOT­0 SLOT­0 SLOT­0 SLOT­0 SLOT­0 SLOT­0 SLOT­0 SLOT­0 SLOT­1 1 2 3 4 5 6 7 8 9 0 3) Enter the starting time using INPUT buttons and press ENTER. · If you have made an error in the input of numbers, press the END button to return to the "MASTER" menu then start from step 2). · The "WEEK SELECT" screen will appear. TIME __:__:__ 4) Use the CURSOR or button to select any day of the week, then select either "YES" or "NO" with ENTER. [. . . ] When using luminance and color-difference signals of HDTV and DVD, connect a Pr/Cr to the R, a Y to the G and a Pb/Cb to the B input of the projector. C S-VIDEO Input Terminal (INPUT A) Connect to the S-video output of the external equipment such as a VCR with an S-video output. This terminal allows switching between S2 and S1 VIDEO input modes. D VIDEO Input Terminal (INPUT A) Connect to the video output of the external equipment such as a VCR or laser disk player. F REMOTE 1 Terminal This terminal allows external control of the projector from either the Switcher or from an external control. When the Switcher is used, connect to the REMOTE 1 terminal on the back of the Switcher. [. . . ]