User manual NEC VT65 QUICK GUIDE

[. . . ] To optimize image, press the AUTO ADJUST button on the cabinet or the remote control. RG INP B UT AU D OU PC -CO N TP 20 Cancel (Right click) Button When you are in the Computer mode, this button works as the mouse right button. When you are in the Projector mode, which is indicated by lighting the PJ button: Press this button to exit "Menus". It works the same way as the "Cancel " button on the cabinet. NOTE: If you are using a Macintosh computer, you can click either the right-click or left-click button to activate the mouse. E 13 PJ Button Press this button to switch the Select, Cancel, and Enter buttons between the Projector mode (lit red)and the Computer mode. [. . . ] RGB Button Press this button to select an RGB source from computer or component equipment connected to your RGB port. Auto Adjust Button Use this button to adjust Position-H/V and Pixel Clock/Phase for an optimal picture. Some signals may not be displayed correctly, or in some cases it may take some time for a source to switch between sources. Select ( ) / (mouse) Buttons When you are in the Computer mode, these buttons work as a computer mouse. When you are in the Projector mode, which is indicated by lighting the PJ button: : Use these buttons to select the menu of the item you wish to adjust. : Use these buttons to change the level of a selected menu item. You can also select the aspect ratio by using the Select or button. If no adustments are performed within 3 seconds, the Aspect Ratio select window will disappear. (See also page E-32. ) 16 17 18 19 20 Help Button Provides information about the current signai and the status of the projector. Picture Mute Button This button turns off the image and sound for a short period of time. V olume Button Press (+) to increase the volume and (­) to decrease it. LE C T EL S O U R C E M E A U TO A D JU S T Monitor PC -CO RG INP B UT AU OU D TP UT IN OU T NT RO L S-V IDE O VID 7 8 O N /O FF ENTER S TA P TU O WS E R P O W S E TA R TU S O CA NC EL S E LE C T Step 2 S O U R C E Connect the supplied power cable. M E NU 9 NU ENTER N /S TA N D B Y CA NC EL S E LE C T U R S O M E C E A U TO A D JU S T RG INP B UT AU D OU TP UT PC -CO NT RO L IN OU T S-V IDE O VID 10 · If the projected image does not appear square to the screen then use keystone correction for proper adjustment. Printed in China 7N8P1131 NOTE: The default is the Computer mode, which allows you to use the Select, Cancel, and Enter buttons as your computer mouse. When the POWER ON/OFF, MENU, HELP or MAGNIFY button is pressed, the PJ button lights red to indicate that you are in the Projector mode. If no buttons are pressed within 10 seconds, the light goes out and the Projector mode is canceled. Basic Menu Source Select RGB Video S-Video Troubleshooting Power/ Status Light Messages Condition Standby Cooling down Lamp in Nomal mode Lamp in Eco mode One minute after lamp is turned on Retrying to turn on lamp Lamp has reached its end of life (2000 hours or over : Normal mode) (3000 hours or over : Eco mode) Lamp life has reached its end of life (2100 hours or over : Normal mode) (3100 hours or over : Eco mode) Lamp or filter cover error (3 locations) Temperature error Fan error Lamp error Common Problems & Solutions Power Indicator Steady orange Blinking green Steady green Steady green Blinking green Steady green Steady green Status Indicator ­ ­ ­ Steady green Depending Lamp mode Blinking orange Steady red Note ­ Blinks green for 60 seconds. The projector is in standby mode and cannot be turned on. Problem Does not turn on Check These Items · Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control is on. · Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (3100 hours in Eco mode). [. . . ] Make sure that you are in the Projector mode or the PJ button lights in red. If not, press the PJ button. Projector Options Menu Setup Menu Menu Mode Language Source Display No Input Display Volume Bar Keystone Bar * Filter Clean Message Menu Display Time Basic/Advanced English/German/French/ Italian/Spanish/Swedish/ Japanese On/Off On/Off On/Off On/Off On/Off Manual/Auto 5 sec/Auto 15 sec/Auto 45 sec * This setting is optional. you need the optional presentation remote control (PR51KIT). Steady orange Steady red Picture is blurred Steady orange Steady orange Steady orange Steady orange Blinking red (1 sec interval) Blinking red (4 sec interval) Blinking red (8 sec interval) Blinking red (12 sec interval) Image is scrolling vertically, horizontally or both Remote control does not work Status indicator is lit or blinking Cross color in RGB mode · See the Power/ Status Light messages. [. . . ]