User manual NEC VERSA MEDIADOCK SERVICE MANUAL

[. . . ] PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Corporation (NEC) and/or its licensors. NEC and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others. The NEC product(s) discussed in this document are warranted in accordance with the terms of the Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon factors such as system configuration, customer data, and operator control. [. . . ] To continue, go to the next section. Setup and Operation 2-13 Creating a Start-Up Diskette A start-up diskette lets you boot your computer with your current configuration. (For details, see the MS-DOS user's guide that came with the Versa. ) 1. From the DOS prompt (C:>), type the following command to format a diskette in drive a: using the /s option. (If you are using a different diskette drive, use the correct drive letter. ) format a: /s 3. At the prompt, insert a blank diskette and press Enter to begin formatting. Once the diskette is formatted, enter a volume name and press Enter or press Enter to skip naming the volume. While the diskette is still in the drive, type the following and press Enter to copy the CONFIG. SYS file to the diskette. copy c:\config. sys a:\*. * 7. Type the following and press Enter to copy the AUTOEXEC. BAT file to disk- ette. copy c:\autoexec. bat a:\*. * 8. Remove the diskette from the drive, label it, and store it in a safe place. Continue as follows: n If the hard disk drive is not the one that came with the Versa, and you have not reformatted the hard disk or reloaded the operating system, go to the next section, "MediaDock Setup Utility. " If you are using a hard disk other than the one that came with the Versa, or the operating system has been reinstalled, go to Appendix A. NOTE: Use the software setup instructions in Appendix B under the following circumstances: -- A hard disk drive other than the one that came with your Versa is installed -- The hard disk drive is reformatted or the operating system is reloaded. n 2-14 Setup and Operation Running the MediaDock Setup Utility This section describes how to use the MediaDock Setup utility. While running the utility, use the following options: n To stop the installation, press Esc. n To accept default settings, press Enter, click "OK, " or click "Continue" at the prompts. n To change settings, follow the on-screen instructions. Before running the MediaDock Setup utility, make sure to enable the MediaDock through the ACU. This procedure is described earlier in this section, "Running the ACU. " Run the MediaDock Setup utility as follows. 1. Close any Windows applications that may be running (for example, CardView). From the Windows Program Manager, access the File pull-down menu and select "Run". 5. Respond to the utility prompts as follows: n n Click "OK" to continue after reading the ACU reminder screen. Click "OK" or press Enter to continue with the setup after reading the MediaDock Setup Utility introduction screen. Press Enter or click "OK" to accept the default subdirectory MEDIADOK. The utility copies the required software into the specified subdirectory. n n 7. If you are using a Versa P, exit Windows and reboot your system to activate the CD-ROM. If you are using an UltraLite Versa, Versa E, Versa M, or Versa V, proceed as follows at the prompt: n Remove the setup diskette, insert Audio Applications diskette 1 into the drive, and press Enter. Setup and Operation 2-15 n The first audio screen tells you to close any applications that are running. [. . . ] Once this procedure is completed, the AUTOEXEC. BAT file contents should look similar to the following. Bold text represents the material entered during this procedure. @ECHO OFF PROMPT $p$g SET PATH=c: \DOS;C:\WINDOWS;C:\NECUTILS;C:\CRYSTAL SET TEMP=C:\TEMP IF NOT EXIST VERSION. GOTO SETUP CLS TYPE VERSION :SETUP C:\DOS\SMARTDRV. EXE LOADHIGH C:\DOS\DOSKEY A-4 Software Setup for Customized Disks SET MOUSE=C:\MOUSE C:\MOUSE\NECMOUSE goto %CONFIG% :MOBILE :MEDIADOCK :END Modify the AUTOEXEC. BAT file as follows. 1. From the DOS prompt, type the following and press Enter. edit AUTOEXEC. BAT 2. [. . . ]