User manual NEC SX10000D

[. . . ] High Light Output Projection System · Großbildschirm Projektions-System SX10000 User's Manual · Bedienungshandbuch SX10000 High Light Output Projection System User's Manual CAUTION: To turn off the main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. Precautions: Please read this manual carefully before using your NEC SX10000 Projector and keep the manual handy for future reference. 3. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. [. . . ] Create data for the master projector and copy data to the slave projector. Choose one projector as the master. Keystone is the distortion of a projected image that usually creates a wider top than bottom. Aiming a projector upward on a wall rather than straight at a wall creates this distortion. Use the or buttons on the slide bar to correct this keystone (trapezoidal) distortion. NOTE: The keystone feature is not available when the test pattern or the blue background is displayed. NOTE: With the projector aimed directly at the screen the maximum keystone angle that can be corrected is +/- 7. 5 degrees. Setting up for Double Stacking in Link Mode 3-1-2. Display all desired input signals, make adjustment to each signal, then save all adjustments on the master projector. NOTE: DO NOT TURN OFF THE POWER while the PC Card Access indicator is flashing. Doing so will cause damage to the data of the projector system. NOTE: Back up your data if you use the supplied CompactFlash card to copy the data from the master projector to the slave projector. The supplied CompactFlash card contains data and firmware for factory use. 3-1-5-2. Press and hold CANCEL, then press POWER on the rear panel of the master projector. The POWER indicator will change to steady green and the PC Card Access indicator will start flashing. After storing data on the PC card, the POWER indicator will change to orange. Transfer the data to the slave projector using the PC card so that all the projectors have the same data in memory. Insert the PC card into the slot of a slave projector. CAUTION: To prevent the projectors from falling, install them in a place and fasten them in a way with sufficient strength to support the two projectors. NOTE: SW 1 Level and SW 2 Level of Switcher Control are not available in Link Mode. 1) Stacking the Projectors 1-1. Place the projectors at the proper height for best screen to projector relationship. Make sure that all projectors have the same display orientation. NOTE: Since data in the slave projector will be lost at this time, make backup copies of them before proceeding. 3-1-6-2. Press and hold ENTER, then press MENU on the rear panel of the slave projector. The POWER indicator will change to steady green and the PC Card Access indicator will start flashing to indicate that the data is being copied from the PC card to the slave projector. After copying data to the slave projector, the POWER indicator will change to orange. E ­ 14 3-1-6-3. Check to see if the images on the master projector are displayed in synchronization with the ones on the other slave projector while the projectors are in link mode. NOTE: If you select the RGB1 input on the master projector, you must select the same input on the slave projector. NOTE: After adjusting and registering signals as mentioned above, you must change the input to RGB on the Entry Edit Command window for Link Mode. [. . . ] Packaged items: SDI board (1), shield case (1), connector cable (1), and installation manual (1) SX HDSDI Board This board accepts the input of non-compressed signal sources such as commercial type digital VCR (D5-VCR) compatible with digital serial component signals (of the SMPTE 292M standard) and provides a high quality image without quantization noise. This board accepts the following image formats. Number of samples of active 1 line 1920 1920x1035/60/2:1 1920 1920x1080/60/2:1 1280 1280x720/60/1:1 1920 1920x1080/24(sF) System Number of active lines in 1 frame 1035 1080 720 1080 Frame rate (Hz) 30 30 60 24 Scanning format 2:1Interlace 2:1Interlace Progressive Progressive Sampling frequency (MHz) 74. 25 74. 25 74. 25 74. 25 Total number of samples in 1 line (dot) 2200 2200 1650 2750 Total number of lines in 1 frame 1125 1125 750 1125 Note that the BNC cable used with the HDSDI connector should be 5C-FB equivalent cable or better. Packaged items: HDSDI board (1), shield case (1), connector cable (2), flat cable (1), set screw for shield case (2) and installation manual (1) REMOTE 3 (XLR) Pin Assignments and Signals REMOTE3 OUT IN IN Pin No. 1 2 3 OUT Signal Ground No connection DATA OUT NOTE: The wireless remote control can operate even if the plug of the remote cable is inserted into REMOTE 3 (XLR) connectors. [. . . ]