User manual NEC SILENTWRITER SUPERSCRIPT 660

[. . . ] Silentwriter SuperScript 660 User's Guide PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Corporation (NEC) and/or its licensers. NEC and/ or its licensers, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others. The NEC product(s) discussed in this document are warranted in accordance with the terms of the Warranty Statement accompanying each product. However, actual perfomance of each such product is dependent upon factors such as system configuration, customer data, and operator control. [. . . ] Cannot scorch, melt, offset, or release emissions when heated to 200° (392° for 0. 1 second. C F) *1 "Single-sheet Feed" refers to the method of placing print media in the hopper one sheet at a time. *2 "Multi-sheet Feed" refers to the method of placing print media in the hopper several sheets at a time for continuous feeding. 6­12 Selecting Paper and Media Table 6-1 Paper Specifications (Cont'd) ITEM Grain Moisture content Opacity Packaging Smoothness Stiffness Wax pick SPECIFICATION Long grain. 12 minimum (Dennison). Selecting Paper and Media 6­13 Envelopes All envelope paper properties must match the paper specifications listed in Table 6-2. Table 6-2 Envelope Specifications ITEM Base weight Calliper Furnish Curl Electrical surface resistivity Finishing SPECIFICATION 75 g/m2 (20 pound), single thickness. Envelope must lie flat, with no more than 0. 25 inch curl across the entire surface. 2. 0 to 15 × 1010 ohms/square (conditioned at 22° C (71. 6° plus 50% relative humidity). Must be accurately folded (±0. 04 inches) so that there are no more than two paper thicknesses anywhere along the envelope surface. All glue lines must be continuous and all folds must be sharply creased. Cannot seal, scorch, melt, offset, or release hazardous emissions when heated to 200° C (392° for 0. 1 second. 100 to 250, Sheffield scale. Fusing capability Moisture content Smoothness 6­14 Selecting Paper and Media All adhesive label paper properties must match the specifications listed in Table 6-3. Table 6-3 Label Specifications Adhesive Labels ITEM Calliper Construction SPECIFICATION No more than 0. 0075 inch (0. 19 mm) The label stock must provide good toner adhesion. General label attachment/die-cutting cannot allow for peeling during transport, printing, or electrical fusing. Zero curl toward image side, minimum 30-degree radius curl toward opposite side. Curl must be within specifications after heating at 200° C (392° for 0. 1 second. Cut sheets must be within ±0. 0313 inch of nominal, corners at 90° ±0. 2° . Cannot scorch, melt, offset, or release hazardous emissions when heated to 200° (392° for 0. 1 C F) second. One year (minimum) stored at 22° (71. 6° at C F) 50% relative humidity. 100 to 250, Sheffield scale. Curl Electrical surface resistivity Electrical volume resistivity Finishing Fusing capability Packaging Shelf life Smoothness Selecting Paper and Media 6­15 Transparency Film All transparency film paper properties must match the specifications listed in Table 6-4. Table 6-4 Transparency Specifications ITEM Cutting dimension tolerance Cutting angle tolerance Thickness Surface treatment SPECIFICATION ±0. 7 mm (±0. 031 in. ) 90° ±0. 2° . Double side. 6­16 Selecting Paper and Media Note the following guidelines when storing paper. To optimize print quality, store and use paper at temperatures no lower than 20° (68° ), with C F humidity of 50%, ±5%. If paper must be stored in extreme humidity, keep it tightly wrapped in plastic. If paper must be stored in extreme cold or hot environments, allow several hours for a temperature adjustment before you use the paper. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Use a shielded and properly grounded I/O cable to ensure compliance of this unit to the specified limits of the rules. Employer Responsibilities Because ozone can be an irritant, various regulatory agencies have established limits to the amount of ozone to which employees may be exposed. The workplace specifications are: A person may not be exposed to an average concentration of greater than 0. 1 part per million (PPM) of ozone for a period of eight hours. [. . . ]