User manual NEC PX-50XR4A

[. . . ] Operation Manual (Enhanced split screen Model) For the specifications of your plasma monitor, refer to "Model Information". NEC Solutions (America), Inc. Important Information Precautions Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference. Do not use this unit's polarized plug with extension cords or outlets unless the prongs can be completely inserted. Avoid damage to the power cord, and do not attempt to modify the power cord. Unplug the power cord during electrical storms or if the unit will not be used over a long period. [. . . ] 1/2 RESET PICTURE MEMORY PREVIOUS PAGE MEMORY4 SET INPUT : -- SIGNAL : -- NOTE : -- MEMORY5 INPUT : -- SIGNAL : -- NOTE : -- MEMORY6 INPUT : -- SIGNAL : -- NOTE : -- SEL. MENU/ENTER OK 2/2 RESET Adjusting the picture The contrast, brightness, sharpness, color and tint can be adjusted as desired. Example: Adjusting the contrast On "CONTRAST" of "PICTURE" menu, adjust the contrast. PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2. 2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. EXIT RETURN G CONTRAST 10 Note: If "CAN NOT ADJUST" appears . . . When trying to enter the PICTURE submenu, make sure PICTURE MODE is not set to DEFAULT. Information Picture adjustment screen CONTRAST: Changes the picture's white level. Adjusting the computer image Only the contrast and brightness can be adjusted when a computer signal is connected. Restoring the factory default settings Select "DEFAULT" under the "PICTURE MODE" settings. EXIT RETURN EXIT RETURN Information PICTURE MEMORY Settings OFF: Picture memory not used. Setting the memory · Use the v and w button to select the desired memory place, MEMORY1 to MEMORY6. · Use the and buttons to select "SET", then press the MENU/ENTER button. Resetting the memory Use the v and w button to select the desired memory place, MEMORY1 to MEMORY6, then use the and buttons to select "RESET", and finally press the MENU/ENTER button. The memory is cleared, and "--" is displayed in the "INPUT", "SIGNAL" and "NOTE" columns. Inputting notes · Use the and buttons to select "NOTE", then press the MENU/ENTER button. · When you have finished inputting the note, press the MENU/ENTER button. Reducing noise in the picture Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor. Example: Setting "NR-3" On "NR" of "PICTURE" menu, select "NR-3". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2. 2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. EXIT RETURN G NR : NR-3 Information NR * "NR" stands for Noise Reduction. The effect becomes stronger as the number increases (in the order NR-1 NR-2 NR-3). OFF: Turns the noise reduction function off. 19 Setting the color temperature Use this procedure to set color tone produced by the plasma display. Example: Setting "HIGH" On "COLOR TEMP. " of "PICTURE" menu, select "HIGH". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : HIGH COLOR TEMP. : 2. 2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. [. . . ] (hereinafter NEC Solutions) warrants this product to be free from defects in material and workmanship under the following terms and, subject to the conditions set forth below, agrees to repair or replace (at NEC Solutions' sole option) any part of the enclosed unit which proves defective. Replacement parts or products may be new or refurbished and will meet specifications of the original parts or products. Parts and Labor: Parts and Labor (Excluding the PDP) are warranted for (3) three years from the date of the first customer purchase. PDP (Plasma Display Panel): The PDP is warranted for (1) one year from the date of the first customer purchase. [. . . ]