User manual NEC POWERMATE PROFESSIONAL 9000E

[. . . ] NEC Computer Systems Division, A Division of Packard Bell NEC, Inc. DECLARATION OF CONFORMITY We, the Responsible Party NEC Computer Systems Division Packard Bell NEC, Inc. 1 Packard Bell Way Sacramento, CA 95828-0903 (916) 388-0101 declare that the product NEC PM Professional 9000E is in conformity with part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Computer Systems Division, Packard Bell NEC, Inc. NEC CSD and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others. [. . . ] In general, set a second, third or fourth IDE device as the master device on the secondary cable, the slave device on the primary cable, and slave device on the secondary cable respectively. Use the table "IDE Connector Configuration" when configuring IDE drives on the primary and secondary IDE connectors on the system board. See "Connecting Device Cables" and "Cabling Storage Devices" for more information on connecting devices. 4-42 Installing Options IDE Connector Configuration Configuration 1 device (hard drive) 2 devices (hard drive, CD-ROM) 2 devices (hard drive, tape backup) 2 devices (hard drive, Zip drive) 3 devices (hard drive, CD-ROM, Zip drive) 3 devices (hard drive, CD-ROM, tape backup) 3 devices (hard drive, hard drive, CD-ROM) 3 devices (hard drive, hard drive, tape backup) 3 devices (hard drive, hard drive, Zip drive) 4 devices (hard drive, CD-ROM, Zip drive, tape backup) 4 devices (hard drive, hard drive, CD-ROM, tape backup) 4 devices (hard drive, hard drive, CD-ROM, Zip drive) 4 devices (hard drive, hard drive, Zip drive, tape backup) Primary connector Master - hard drive Slave - none Master - hard drive Slave - none Master - hard drive Slave - none Master - hard drive Slave - none Master - hard drive Slave - none Master - hard drive Slave - none Master - hard drive Slave - hard drive Master - hard drive Slave - hard drive Master - hard drive Slave - hard drive Master - hard drive Slave - Zip drive Master - hard drive Slave - hard drive Master - hard drive Slave - hard drive Master - hard drive Slave - hard drive Secondary connector Master - none Slave - none Master - CD-ROM Slave - none Master - tape backup Slave - none Master - Zip drive Slave - none Master - CD-ROM Slave - Zip drive Master - CD-ROM Slave - tape backup Master - CD-ROM Slave - none Master - tape backup Slave - none Master - Zip drive Slave - none Master - CD-ROM Slave - tape backup Master - CD-ROM Slave - tape backup Master - CD-ROM Slave - Zip drive Master - Zip drive Slave - tape backup Installing Options 4-43 Connecting Device Cables The cables used for installing optional storage devices include: T T T T T diskette drive signal cable IDE signal cables internal SCSI device cables PC adapter card cables system power cables. System board drive cable connectors are shown in the following figures. System board cable connectors A ­ Diskette Drive Connector B ­ Primary IDE Connector C ­ Secondary IDE Connector D ­ Narrow SCSI Connector E ­ Wide SCSI Connector 4-44 Installing Options System board auxiliary cable connectors A ­ Serial Port B (COM2) Connector B ­ USB Connector C ­ Chassis Intrusion Alarm Connector D ­ System Fan Connector E ­ Not Used Diskette Drive Signal Cable A three-connector diskette drive signal cable comes attached to the system board and to the standard 1. 44-MB diskette drive. A second diskette drive can be connected to the middle connector on the diskette drive cable. Align the red edge of the cable with pin 1 (the notched end) on the drive connector. Installing Options 4-45 The following figure shows the three-connector diskette drive signal cable. Diskette drive signal cable A ­ Connects to 1. 44-MB Diskette Drive B ­ Connects to System Board 4-46 Installing Options IDE Signal Cables Systems come with two 3-connector IDE interface cables. If one of the cables is not used, it is provided with the system but not connected. If the IDE cable is not keyed with a connector tab, align the colored edge of the cable with the pin 1 side of the drive connector. IDE cable A ­ Connects to System Board IDE Port B ­ Connects to IDE Device Installing Options 4-47 Internal SCSI Device Cables Systems that have an internal SCSI device also come with either a six-connector 68-pin SCSI device cable or a fourconnector 50-pin SCSI device cable. The cables can connect internal SCSI devices to the 68-pin and/or the 50-pin internal connectors on the system board. The unused connectors on the cable are terminated. SCSI device cable A ­ Connects to System Board B ­ Connect to SCSI Devices 4-48 Installing Options PC Card Adapter Cable Two PCMCIA-compliant cables come with the PC card adapter available in some systems. The cables are bound together, and connect to the dual PCMCIA ports on the PC adapter board and the connectors on the back of the PC card adapter. System Power Cables Power cables come from the power supply and are attached to the standard storage devices. System power cables vary in length and provide connector sizes to accommodate a variety of supported storage configurations. The following figure shows the power cable connectors. Power cable connectors A ­ Small Power Cable Connector B ­ Large Power Cable Connector Installing Options 4-49 Cabling Storage Devices All storage devices require power and signal cable connections. Your computer supports four types of cabled storage devices: T IDE devices -- includes hard drive, Zip drive, tape backup unit, or CD-ROM drive T diskette drive -- 1. 44-MB drive T PC card adapter (with a PC adapter card) T SCSI devices. IDE Drive Cabling The following procedure describes how to cable an IDE drive. Note: The appearance of your device may vary from the one shown. 1. Locate an available power connector coming from the power supply. 4-50 Installing Options 3. Connect the appropriate power cable to the power connector on the IDE drive. Connecting IDE drive cables A ­ IDE Cable B ­ Power Cable 4. If you are installing a CD-ROM drive and your system has speakers, connect the audio cable to the CD In connector on the sound board (see the instructions that come with the drive). Installing Options 4-51 Diskette Drive Cabling The following procedure explains how to cable a diskette drive. Connect the diskette drive signal cable connector to the signal connector on the diskette drive. Connect the power cable to the power connector on the device. PC Card Adapter Cabling The following procedure describes how to cable a PC card adapter. Connect the connectors at one end of the cable set to the PC adapter board. See "Installing an Expansion Board" if the board must be installed first. ) The connectors are keyed to fit only one way. Connect the connectors at the other end of the cable set to the connectors at the rear of the PC card adapter. 4-52 Installing Options Internal SCSI Device Cabling To connect an internal SCSI device, perform the following steps: 1. Connect the SCSI device to the last free connector on the SCSI device cable (see the following figure). A ­ SCSI Cable B ­ Power Cable 2. [. . . ] Random access memory specifications, B-3 Read only memory specifications, B-3 Removing battery, 5-28 drive cage, 4-65 expansion boards, 4-38 memory, 4-17 processor, 4-21 termination board, 4-23 top cover, 4-9 P Padlock slot, 2-7 Panel removing, 4-55 Parallel port, 3-12 PC card adapter, 1-6 cable, 4-44, 4-49 cabling, 4-50, 4-52 specifications, B-9 PC card slot, 1-6 PC cards, 1-6 PC97, 1-17 Pentium II, 1-17 Index-5 Repair service, 5-31 Repartitioning the hard drive, 3-24 Replacing 5 1/4-inch device, 4-54 battery, 5-26 drive cage, 4-65 expansion boards, 4-35 processor, 4-28 side covers, 4-8 top cover, 4-9 Restoring applications, 3-32 ROM. See Read only memory. S Safety precautions, 4-3 before shipping, 2-13 option installation, 4-3 system unit stand, 1-14 SCSI device cable, 4-44 cabling, 4-50, 4-53 Secondary device, 4-43 Secure mode, 1-23 Security, 1-23, 2-7 chassis intrusion notification, 1-24 chassis locking tab, 1-24 Kensington Security Standard connector, 1-24 password, 1-23 unattended start, 1-23 Windows, 1-23 Select Install CD. Serial port, 1-8 Shipping, 2-13 preparations, 2-13 Shutdown, 2-9 Side covers replacing, 4-8 Slave device, 4-43 Software features, 1-20 Sound system specifications, B-4, B-7 Speakers, 1-16 AC adapter, 1-16 specifications, B-11 Specifications cache memory, B-3 calendar clock, B-3 CD-ROM drive, B-9 compliance, B-13 fax/modem board, B-8 hard drive, B-8 keyboard, B-12 operating environment, B-12 PC card adapter, B-9 power, B-12 processor, B-2 Random Access Memory (RAM), B-3 read only memory (ROM), B-3 sound system, B-4, B-7 Speakers, B-11 system unit dimensions, B-12 tape backup unit, B-9 Zip drive, B-10 Speed DIMM, 4-14 processor, 3-6 Stand, 1-14, 4-2 Storage device installation, 4-40, 4-54 cables, 4-44 device bays, 4-40 device preparation, 4-41 Index-6 Strain-relief loop, 4-4 System shutdown, 2-9 specifications, B-12 System board connectors, 1-12, 4-12, 4-34, 4-44, 4-45 jumper settings, 3-39 locating jumpers, 3-40 options, 4-12 System Board Management Controller, 1-19 System fan, 1-11 System memory, 1-19 checking, 4-16 System unit cleaning, 2-12 covers, 4-4 User's guide online documentation, 1-22 Utilities Network Associate VirusScan, 1-22 V VirusScan, 1-22 Voltage selection, 2-4 Voltage selector switch, 1-11 W Wake-On LAN cabling, 4-37, 4-54 connector, 4-38 Windows NT installing, 3-24 Z Zip drive, 1-6 cables. specifications, B-9 termination board removing, 4-23 Top cover removing, 4-9 replacing, 4-9, 4-65 Troubleshooting, 5-2 U Upgrading BIOS, 3-17 DIMMs, 4-13 memory, 4-12, 4-13 processor, 4-12, 4-20, 4-28 USB port, 1-10, 1-19 Index-7 (For United States Use Only) Federal Communications Commission Radio Frequency Interference Statement WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]