User manual NEC PLASMASYNC PX-50XM2A

[. . . ] PlasmaSync Plasma Monitor User's Manual NEC Technologies Important Information Precautions Please read this manual carefully before using your NEC plasma monitor and keep the manual handy for future reference. Warnings and Safety Precaution The NEC plasma monitor is designed and manufactured to provide long, trouble-free service. Never use solvents such as alcohol or thinner to clean the panel surface. Although NEC produces the plasma display panels with more than 99. 99 percent active cells, there may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. [. . . ] Use the L and M buttons to select "SOUND", then press the PROCEED button. Use the L and M buttons to select "BASS". SOUND BASS TREBLE BALANCE L R To continue adjusting the sound . . . To delete the main menu, press the EXIT button once more. Note : If "CAN NOT ADJUST" appears. . . Restoring the factory default settings Select "RESET" under the function menu. Note that this also restores other settings to the factory defaults. SEL. ADJ. EXIT RETURN 3. Adjust the bass using the and buttons. SOUND BASS TREBLE BALANCE L R SEL. ADJ. EXIT RETURN * If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears. 25 Screen Settings Menu Adjusting the Position, Size, Fine Picture, Picture Adj The position of the image can be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position in the normal mode Press the PROCEED button on the remote control to display the MAIN MENU on the screen, then. . . Use the L and M buttons to select "SCREEN", then press the PROCEED button. Default settings (when RGB/PC is selected) SCREEN : NORMAL MODE V­POSITION H­POSITION V­HEIGHT H­WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. Adjust using the and buttons. V­POSITION * If neither the or button is pressed within 5 seconds, the current setting is set and the previous screen reappears. To delete the main menu, press the EXIT button once more. Information When "AUTO PICTURE" is "OFF" SCREEN : FULL MODE V­POSITION H­POSITION V­HEIGHT H­WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. EXIT RETURN * The settings on the SCREEN menu are not preset at the factory. The mode switches as follows when the buttons are pressed: NORMAL FULL and * The mode can also be switched by pressing the "WIDE" button on the remote control. Use the L and M buttons to select "V-POSITION". SCREEN : NORMAL MODE V­POSITION H­POSITION V­HEIGHT H­WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. EXIT RETURN When Auto Picture is off, the Fine Picture and the Picture ADJ. items are displayed so that you can adjust them. 26 Information Adjusting the Auto Picture ON . . . . . . . . . . . . . . . . . . . * The Picture ADJ and Fine Picture features are available only when the "Auto Picture" is off. Restoring the factory default settings Select "RESET" under the function menu. Note that this also restores other settings to the factory defaults except for Auto Picture. Function Settings Menu Setting the on-screen menu When using the monitor for presentations, etc. , the monitor can be set so that the input source, screen mode, etc. , do not appear. Example: Turning the on-screen menu mode off Press the PROCEED button on the remote control to display the MAIN MENU on the screen, then. . . Use the L and M buttons to select "FUNCTION", then press the PROCEED button. The mode switches as follows each time the button is pressed: ON OFF FUNCTION : OFF :1 : OFF :3 : ON :1 or OSM OSM ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. To delete the main menu, press the EXIT button once more. Information OSM modes ON . . . . . . . . . . . . . . . . . . . [. . . ] of the United States. 56 Troubleshooting If the picture quality is poor or there is some other problem, check the adjustments, operations, etc. , before requesting service. Symptom Checks Remedy · Leave some space between the display and the connected components. · Point the remote control at the monitor's remote control sensor when pressing buttons, or remove the obstacle. · Eliminate the light by closing curtains, pointing the light in a different direction, etc. · Press the "WIDE" button on the remote control and adjust properly. [. . . ]