User manual NEC PLASMASYNC PX-42VM2A

[. . . ] PlasmaSync Plasma Monitor User's Manual NEC Technologies Important Information Precautions Please read this manual carefully before using your NEC plasma monitor and keep the manual handy for future reference. Warnings and Safety Precaution The NEC plasma monitor is designed and manufactured to provide long, trouble-free service. Never use solvents such as alcohol or thinner to clean the panel surface. Although NEC produces the plasma display panels with more than 99. 99 percent active cells, there may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. [. . . ] Use the v and w buttons to select "PICTURE MODE". PICTURE CONTRAST BRIGHTNESS SHARPNESS COLOR TINT R PICTURE MODE : MEMORY COLOR TEMP. The picture mode is set to "THEATER". PICTURE CONTRAST BRIGHTNESS SHARPNESS COLOR TINT R PICTURE MODE : THEATER COLOR TEMP. To delete the main menu, press the "EXIT" button once more. Information G EXIT RETURN 3. The mode switches as follows when the and buttons are pressed: MEMORY THEATER NORMAL RESET Types of picture modes MEMORY . . . . . . This mode provides darker, finer pictures, like the screen in movie theaters. CONTRAST = 80% for RESET mode BRIGHTNESS = 95% for RESET mode NORMAL . . . . . . . This mode provides dynamic pictures with distinct differences between light and dark sections. Use this to reset the picture to the factory default settings. PICTURE MODE : THEATER * If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears. 19 Setting the color temperature Use this procedure to set color tone produced by the plasma display. Example: Setting "1" Press the PROCEED button on the remote controller to display the MAIN MENU on the screen, then. . . Use the v and w buttons to select "PICTURE", then press the "PROCEED" button. Use the v and w buttons to select "COLOR TEMP. ". PICTURE CONTRAST BRIGHTNESS SHARPNESS COLOR TINT R PICTURE MODE : MEMORY COLOR TEMP. To delete the main menu, press the "EXIT" button once more. Information Setting the color temperature 1 . . . . . . . . . . . . . . . . . . . . . . . . . Low (redder) Restoring the factory default settings Select "RESET" under the function menu. Note that this also restores other settings to the factory defaults. G EXIT RETURN 3. The mode switches as follows when the buttons are pressed: 1 2 3 PRO and * See page 21 to set "PRO". COLOR TEMP. : 1 If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reppears. The "COLOR TEMP. " is set to "1". PICTURE CONTRAST BRIGHTNESS SHARPNESS COLOR TINT PICTURE MODE COLOR TEMP. ADJ. R G : MEMORY :1 : NR-2 EXIT RETURN 20 Adjusting the color to the desired quality Use this procedure to adjust the white balance for bright pictures and dark pictures to achieve the desired color quality. Example: Adjusting the "WHITE BALANCE" Press the PROCEED button on the remote controller to display the MAIN MENU on the screen, then. . . Use the v and w buttons to select "PICTURE", then press the "PROCEED" button. Use the v and w buttons to select "COLOR TEMP. ". PICTURE CONTRAST BRIGHTNESS SHARPNESS COLOR TINT R PICTURE MODE : MEMORY COLOR TEMP. Use the v and w buttons to select "RED-GAIN". WHITE BALANCE GAIN RED GREEN BLUE BIAS RED GREEN BLUE SEL. ADJ. EXIT RETURN 6. Adjusts the white balance using the and buttons. G EXIT RETURN R-GAIN 3. [. . . ] * "Apple Macintosh" is a registered trademark of Apple Computer, Inc. of the United States. 44 Troubleshooting If the picture quality is poor or there is some other problem, check the adjustments, operations, etc. , before requesting service. Symptom Picture is disturbed. Monitor's power does not turn on when the remote controller's power button is pressed. Checks · Is a connected component set directly in front or at the side of the display? Remedy · Leave some space between the display and the connected components. · Are the remote controller's batteries worn out?· Is the monitor's power cord plugged into a power outlet? [. . . ]