User manual NEC MULTISYNC MD21GS3MP QUICK START

[. . . ] TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. [. . . ] If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference Problems. " This booklet is available from the U. S. Declaration of the Manufacturer We hereby certify that the grayscale monitor MD21GS-3MP is in compliance with Council Directive 93/42/EEC: ­ EN 60601-1 ­ EN 60601-1-2 ­ EN 61000-3-2 ­ EN 61000-3-3 and marked with CE. NEC-Mitsubishi Electric Visual, Systems Corporation, 4-13-23, Shibaura, Minato-Ku, Tokyo 1080023, Japan 2 MD21GS3MPquickstart. p65 2 7/22/04, 9:52 AM Contents Your new NEC Display monitor box* should contain the following: · · · · · · MD21GS-3MP Display with tilt/swivel/pivot/height adjustable stand Power Cords (N. A. Hospital Grade, Europe Continental and Chinese*2) Quick Reference & Setup Guide Installation and Maintenance Guide CD-ROM (GammaComp MD) Video Signal Cable (DVI-D to DVI-D cable) Power Cord Video Signal Cable INSTALLATION & MAINTENANCE GUIDE QUICK REFERENCE & SETUP GUIDE MD21GS-3MP MD21GS-3MP Quick Reference Guide Installation and Maintenance Guide CD-ROM * Remember to save your original box and packing material to transport or ship the monitor. *2 For Japanese market model, only power cord for Japan is provided with this monitor. 3 MD21GS3MPquickstart. p65 3 7/22/04, 9:52 AM Quick Start Optional Display Card Installation 1. Following your PC manufacturer's guidelines, open your computer to access a PCI slot. Place the display card into an available PCI slot and secure all screws. NOTE: For installing driver information, display modes in multimonitor mode, the setting the dip switch, please reference the display card manufacturer's documentation. Connecting the LCD to Your PC Once the display card is successfully installed, following these instructions to connect the display to your PC. Connect the DVI-D signal cable to the connector of the display card in your system (Figure A. 1). NOTE: for dual displays, plug a DVI-D cable into Port 2 of the display card (Figure A. 1). Connect the DVI-D signal cable to the connector on the back of the display (Figure C. 1). NOTE: Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module, and/or shorten the module life. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet (Figure C. 1). NOTE: Refer to the Display Adjustment & Mounting section to check tilt, raise and lower monitor screen and screen rotation when you manage cables and power cord. NOTE: Please refer to the Caution section of this manual for proper selection of AC power cord. Collect cables and power cord and place them under the cable clip (Figure B. 1). NOTE: Release the cables from the clip before removing the cable cover. Turn on the monitor with the power switch on the top (portrait) or left side (landscape) of the monitor (Figure D1). For further adjustments, please refer to the OSM section for a full description of OSM controls. NOTE: If you have any problems, refer to the Troubleshooting section. 4 MD21GS3MPquickstart. p65 4 7/22/04, 9:52 AM Quick Start ­continued Figure A. 1 Figure B. 1 Port 2 for Dual Monitor Figure C. 1 Figure D. 1 5 MD21GS3MPquickstart. p65 5 7/22/04, 9:52 AM User Controls 1. [. . . ] · Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources. · The power cable connector is the primary means of detaching the system from the power supply. The monitor should be installed close to a power outlet which is easily accessible. [. . . ]