User manual NEC MT840-1040-1045

[. . . ] LCD Projector MultiSync MT840/MT1040/MT1045 User's Manual IMPORTANT INFORMATION Precautions Please read this manual carefully before using your NEC MultiSync MT840/MT1040/MT1045 Projector and keep the manual handy for future reference. Your serial number is located under the name plate label on the left side of your MultiSync MT840/MT1040/ MT1045. Record it here: CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. [. . . ] NOTE: You can close the main and sub menus simultaneously by pressing the Computer/Projector Select button to cancel the Projector mode. Repeat steps 2-5 to adjust an additional item, or press "Cancel" on the projector cabinet or the remote control to quit the menu display. Using a USB Mouse Using a USB mouse gives you a smooth operation. NOTE:There may be some brands of USB mouse that the projector does not support. Operate the Menus using the USB mouse Mouse Cursor When connecting a USB mouse to the projector, you get a mouse cursor on the screen. Unless you use your USB mouse within 10 seconds, the mouse cursor disappears. Adjusting and Setting Display You can select a menu item and click with a mouse button to make adjustments and setting. Examples Click (or press and hold) the mouse button or to adjust the brightness. Or click and drag the mouse button on the slide bar horizontally to adjust it. If you click anywhere in the background while displaying adjustment and setting menu or dialog box, you will get the main menu at the clicking point. IMPORTANT: · The projector should be unplugged if it will not to be used for an extended period. · To turn off the image and sound briefly (five minutes or less), use the "Picture Mute" button instead of turning the projector off and on. · The projector will display a black, blue image or logo if no input signal is present. After the projector turns off, the cooling fans keep operating for a full minute. Do not disconnect the power cable during this time. Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. Press the "Menu" button on the remote control or projector cabinet to display the Main Menu. NOTE: When using a USB mouse, click the mouse button to display the main menu. For other operations, do the same way as you use your PC mouse. E­17 MENU Tree Main Menu Mein Menu Source Select Adjustments Image Options Projector Options Tools Help Sub Menu Source Select RGB 1 RGB 2 Video S-Video PC Card Viewer Items Adjustable Sources Brightness* Contrast* Color* Hue* Sharpness* Auto Adjust** Position** Pixel Adjust** Resolution** All Data/Current Signal R, V, C R, V, C V, C V, C V R R R R Adjustments Picture Volume Image Color Temperature Keystone Factory Default Image Options Image Mode Video Mode R, V, C All All Aspect Ratio Gamma Noise Reduction Color Matrix Language Source Display Projector Pointer Orientation Background Signal Select Auto Start Power Management Power Off Confirmation Mouse Button Mouse Sensitivity Clear Lamp Hour Meter Keystone Save Fan High Speed Mode Remote Sensor S-Video Mode Select PC Card Viewer Options Capture Options Source Name Input Terminal Frequency FH Frequency FV Sync Polarity Signal Type Video Type Sync Type Interlace Resolution Aspect Ratio Gamma Noise Reduction Color Matrix Matrix Type Lamp Hour Meter V, C R, V, C V, C C Projector Options Menu Setup Tools Capture PC Card Files ChalkBoard Help Contents Source Information Projector Information NOTE: Adjustable sources R=RGB V=Video/S-Video C=Component All=All sources (including PC Card Viewer) E­18 Menu Elements Title bar Setup Page1 Page2 Page3 Page4 Orientation Signal Select RGB1 RGB2 Background Blue Video S-Video Auto Auto Auto Auto Tab Close button Highlight Solid triangle Front Floor OK Cancel Cancel Button OK Button Setup Page1 Page2 Page3 Page4 Check box Mouse Button Right Hand Auto Start Left Hand Slow Power Management Power Off Confirmation Keystone Save Clear Lamp Hour Mater Fan High Speed Mode Radio button Sensitivity Fast Medium OK Cancel Slide bar Brightness Menu windows or dialog box typically have the following elements: Title bar: Indicates the menu title. Radio button: Use this round button to select an option in a dialog box. You will return to the previous menu. E­19 Menu Descriptions & Functions Source Select Source Select RGB 1 RGB 2 Video S-Video PC Card Viewer Enables you to select a video source such as a VCR, DVD player, laser disc player, computer or document camera depending on what is connected to your inputs. Press the "Select" button on the projector cabinet or vw buttons on your remote control to highlight the menu for the item you want to adjust. Play/Stop: Plays back automatically or manually depending on the setting on PC Card Viewer Options of the menu. This allows you to stop Auto Play while you are playing back and to resume playing from the selected slide or folder when "Auto Play" is selected. This allows you to move on to the next slide when "Manual Play" is selected. Displays a list of folders while you are playing back. Delete: Deletes a captured slide(s) or all the captured slides in the selected folder. Clicking with the right button of a mouse shows it again. RGB1 and 2 Selects the computer connected to your RGB or component signal. [. . . ] · Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (1600 hours : MT1045). If there is insufficient ventilation around the projector or if the room where you're presenting is particularly warm, move the projector to a cooler location. · · · · · Use the menu to select your source (Video, S-Video, RGB or PC Card Viewer). Reset the settings or adjustments to factory preset levels using the Factory Default in the Adjustment Menu. [. . . ]