User manual NEC MT800

[. . . ] REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL. RF Interference WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Technologies in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. [. . . ] ENTER: Stores the setting or adjustments. General Controls Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. Turn on the Projector Plug the supplied power cable in the wall outlet. The projector will go into its standby mode and the power indicator will glow amber. Only after you press the "On" button on the projector cabinet or the full function remote control will the power indicator turn to green and the projector become ready to use. NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the "Auto Start" feature. Select the Computer, Video Source or PC Card Viewer Press the Source button on the remote control or the projector cabinet to select "Video" (VCR, document camera, or laser disc player), S-Video", "RGB 1 / 2" (computer or DVD with component output) or "PC Card Viewer" to display the image. Or press the "Menu" button on the remote control or the cabinet and use the menu to select your video source: "Video", "S-Video", "RGB1 / 2", or "PC Card Viewer". Adjust the Image Size and the Focus Use the Zoom ring to adjust the image size, then use the Focus ring knob to obtain the best focus. Use the "Magnify" button (+) or (-) on the remote control to make the image larger up to 400%. Turning off the Projector First press the "off" button on the projector cabinet or the remote control for a minimum of two seconds. The power indicator will go out. CANCEL: Return to the previous screen without storing settings or adjustments. NOTE: An optional component cable (Component V cable) is needed for a component signal. Select "Component" from the Input Signal submenu to display the component signal. Adjustments Adjustments Picture Volume Image Color Temperature Keystone Factory Default Video Selects what is connected to your Video input-VCR, laser disc player, DVD player or document camera. Provides access to controls for your image and sound. Use the "Select" button on the projector cabinet or vw buttons on your remote control to highlight the menu for the item you want to adjust. S-Video Selects what is connected to your S-Video input-VCR, DVD player, or laser disc player. NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or S-Video source. Brightness PC Card Viewer This feature enables you to make presentations using a PC card that contains captured images and slides created with the exclusive PC Card Viewer Utility contained in the CD-ROM. The starting screen for the PC Card Viewer varies depending on the settings of the Setup's Page 3. NOTE: Even if you switch the current PC Card Viewer source to another source, the current slide is retained. When you return back to the PC Card Viewer, you will get the slide that has been retained. A launcher will appear when you press the MENU button. Prev Play/Stop Select View Drag Picture (not available for PC Card Viewer) Brightness: Contrast: Color: Hue: Adjusts the brightness level or the back raster intensity. Increases or decreases the color saturation level (not valid for RGB). This adjustment is only valid for Video and Component inputs (Not RGB). Controls the detail of the image for Video (Not for RGB and Component). Sharpness: Volume (not available for PC Card Viewer) Next Jump Delete Adjusts the sound level of the projector. The launcher is a tool bar including the following buttons: Drag: Prev: Next: Drags to move the tool bar. [. . . ] If the room temperature is high, move the projector to a cooler location. If the temperature inside the projector is high, check the cooling fan hole on the bottom of the projector. Turn off the projector, wait one minute, then turn the projector back on. Or the lamp is burnt out. Common Problems & Solutions Problem Does not turn on Check These Items · Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control is on. [. . . ]