User manual NEC MT1065

[. . . ] LCD Projector MT1075/MT1065 User's Manual LIMITED WARRANTY Except as specified below, the warranty that may be provided by the dealer covers all defects in material or workmanship in this product. Any product on which the serial number has been defaced, modified or removed. Accident, misuse, abuse, neglect, fire, water, dust, smoke, lightning or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. Cartons, carrying cases, batteries, external cabinets, CDROM, or anyaccessories used in connection with the product. [. . . ] See the user's manual or the quick connect guide for projecting an image. The 3D Reform (Cornerstone) screen is displayed. Screen's outer frame 5. Processing takes about 20 seconds * To cancel, use the SELECT or button to highlight [Cancel] and press the ENTER button. Projected area 3. A guide pattern that shows available area for Auto 3D Reform is displayed. button on the remote control can also be used for this purpose. NOTE: * When "4:3 Fill" is selected in "Aspect", the Auto 3D Reform feature is not available. * If the screen's outer frame is larger than gray area of the guide pattern as shown, the Auto 3D Reform feature does not function. * In the Auto 3D Reform mode, when controlling the projector using PC control, you might not be able to make correction. (The projector can be operated with Dynamic Image Utility 2. 0, Image Express Utility 1. 0 and HTTP Server function. ) Not recommended E-25 Setting Screen of Auto 3D Reform 1. Use the SELECT or button to highlight "To Advanced Menu" and press the ENTER button. The "Auto Functions" screen is displayed. Focus . . . . . . . . . . . . . If the built-in sensor sensitivity is so strong that it recognizes even lines within the screen, select "Lower". If the built-in sensor sensitivity is too weak to recognize the screen, select "Higher". NOTE: If you failed to correct for placing the image inside of the screen using [Inside], the projector automatically corrects to project the image larger than the outer frame of the screen. E-26 Turning Off the Image and Sound Press the Picture Mute button to turn off the image and sound for a short period of time. Press again to restore the image and sound. Enlarging and Moving a Picture You can enlarge the area you want up to 400 percent. Press the Pointer button to display the pointer. POINTER Freezing a Picture Press the Freeze button to freeze a picture. Move the pointer to the area you want to enlarge. Using the Pointer You can use one of nine pointers to draw your audience's attention to the portion of a projected image you want. SELECT POINTER 3. To move the magnified image, use the SELECT button. MAGNIFY Press the Pointer button to display the pointer. Press the Pointer button to display the pointer. 4. Return the image to the original size. MAGNIFY SELECT Use the Select button to move the pointer. Use the Select button to move the pointer. Getting the On-line Help You get the contents about Help. HELP SELECT Display Help Exit Help E-27 Using a USB Mouse Using a USB mouse gives you a smooth operation. A commercially available USB mouse is required. Using the USB HUB Function When using the projector with a PC via the supplied USB cable, both the USB port(type A) on the projector can be connected to a USB-supported scanner or other USB-supported device. (USB Hub Function) Example: When connecting a PC and a scanner to each USB port respectively USB(MOUSE/HUB) USB(MOUSE/HUB) USB(PC) NOTE: · The MT1065 comes with a USB mouse. · There may be some brands of USB mouse that the projector does not support. An example of how a scanned image is projected 1. Install the Dynamic Image Utility on your PC. Operate the Menus using the USB mouse Mouse Cursor When connecting a USB mouse to the projector, you get a mouse cursor on the screen. Unless you use your USB mouse within 10 seconds, the mouse cursor disappears. [. . . ] : Local Contact office : Local Contact office Address : Phone No. , Fax No. on cabinet : Problem of units per User : Required Service : Requested period of Loan unit : Payment method : In Case of Credit Card : Card No. w/Valid Date : (1) Credit Card (2) Travelers Cheque (3) Cash (1) Repair and Return (2) Loan unit E-68 Condition of your TravelCare Service Program Enduser is requested to understand following condition of TravelCare Service Program and complete the necessary information on the application sheet. Enduser has to understand following condition and is required to fill in the Application Sheet. [. . . ]