User manual NEC MT1035

[. . . ] MultiSync MT1035 NEC Multimedia Theatre NEC Multimedia Theatre NEC Technologies, Inc. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 LCD Projector User's Manual NEC Technologies ® TM Part No. 78409631 Printed in Japan IMPORTANT INFORMATION CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket the should be installed as near to quipment as possible, and should be easily accessible. 1 Precautions Please read this manual carefully before using your NEC MultiSync MT1035 LCD Projector and keep the manual handy for future reference. [. . . ] If you're projecting the image from the rear and your image is inverted, use the "Menu" and "Select" buttons on your projector cabinet or (v) (w) buttons on your remote control to correct the image. (See page 70 . ) 23 INSTALLATION 44 45 Wiring Diagram To video, S-video, and audio inputs on the LCD Projector. VCR, DVD Player or LaserDisc Player Monitor PC CONTROL MOUSE OUTPUT R GB M ON I TOR OU TP U T L / M ON O R AUDIO REMOTE CONTROL INPUT S ­V I D E O I N P U T AUDIO R GB INPUT 1 AUDIO R GB INPUT 2 AUDIO L / M ON O VIDEO INPUT AUDIO R Remote cable Mouse adapter (For Macintosh) Macintosh or Compatibles (Desk top type) Pin adapter for Macintosh (supplied) Mouse adapter (For IBM PS/2) IBM VGA or Compatibles Document Camera Signal cable (supplied) To mini D-Sub 15-pin connector on the LCD Projector. Remote Control Guideline 1. Plug the serial cable with the mouse output port of the projector into your computer's mouse port and restart your computer to gain remote mouse control. When using the remote control's built-in infrared mouse on a laptop computer, the laptop's mouse, trackball or trackpad will be disabled. Disconnect the serial cable from the mouse output port and restart your computer to regain trackball or trackpad mouse control. If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software. If you accidentally hit the OFF button on the remote control, wait one full minute and then press the ON button to resume. 24 INSTALLATION 46 47 Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to your MultiSync MT1035 (XGA) Projector will enable you to project your computer's screen image for an impressive presentation. All of these following display standards are supported: VGA 640 480 for graphics VGA 640 400 for graphics VGA 640 350 for graphics VGA 720 400 for text VGA 720 350 for text SuperVGA 800 600 Macintosh at 640 480 Macintosh at 832 624 XGA1024 768 Macintosh at 1024 768 SXGA1280 1024 (Accu-Blend) To connect to a PC, Macintosh or computer equipped with an XGA/ SVGA /VGA adapter or compatible graphics adapter, simply: 1. If your PC does not support XGA/SVGA/VGA you will need to install an XGA/SVGA/VGA graphics board. Consult your computer's owner's manual for your XGA/SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for installation instructions. 3. Use the signal cable that's supplied to connect your PC or Macintosh computer to the projector. For a Macintosh, use the supplied pin adapter to connect to your Mac's video port. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the projector. When using a Macintosh with the MT1035, set the DIP switches of the supplied pin adapter according to your resolution. · When using with a Macintosh, XGA/VGA/SVGA (1024 768) is recommended if your Macintosh supports this mode. · When using with a Macintosh PowerBook, output may not be set to 1024 768 unless "mirroring" is off on your PowerBook. Refer to owner's manual supplied with your Macintosh computer for mirroring. NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub 15pin connector. Settings for Monitor Mode Number of DIP switch S1 S2 S3 S4 S5 S6 S7 S8 Monitor size 15" multi-scan mode /16"­13" 17" multi-scan mode /19"­13" 19" multi-scan mode /21"­13" 13" fixed mode /640 480 VGA/SVGA mode 16" fixed mode /832 624 19" fixed mode /1024 768 ON ON ON ON ON ON ON ON ON ON NOTE: For settings other than display modes supported by your Macintosh and MT1035, use of the DIP switch may bounce a image slightly or may display nothing. If this happens, set the DIP switch to the 13" fixed mode and then restart your Macintosh. After that, restore to a displayable mode and then restart the Macintosh again. [. . . ] Status Blinking very rapidly (On and off in a cycle of 1 sec. ) Blinking rapidly (On and off in a cycle of 4 sec. ) Blinking slowly (On and off in a cycle of 8 sec. ) Blinking very slowly (On and off in a cycle of 12 sec. ) The cooling fan has stopped. Turn off the projector, wait one minute, then turn the projector back on. Or the lamp is burnt out. 45 TROUBLE SHOOTING 88 89 Common Problems & Solutions Problem Does not turn on Check These Items · Check that the cord is plugged in and that the power switch on the front panel is on. (See page 82. ) · Check the status light to see if the projector has overheated or the lamp usage exceeds 2100 hours. [. . . ]