User manual NEC MOBILEPRO 750C VERSION 1998

[. . . ] NEC MobilePro 750C User's Guide PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Computer Systems Division, Packard Bell NEC, Inc. NECCSD and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others. The NECCSD product(s) discussed in this document are warranted in accordance with the terms of the Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon factors such as system configuration, customer data, and operator control. [. . . ] Be sure you have the "Quick Launch" tab selected. 3-6 Using the MobilePro Settings dialog box 3. As- sign the application using the following buttons: T T Default -- selects the factory-assigned application listed in the Default Application Shortcut Keys table. Browse -- opens a directory dialog so you can locate the application you want to assign. Browse dialog box Using the MobilePro 3-7 T Delete -- removes the currently assigned application reference so you can select another application. ENABLING THE DISPLAY LINKAGE SWITCH You can configure your MobilePro H/PC to power on or off by simply opening or closing the display cover. The display linkage switch acts as a switch for both the power and the backlight. Closing the MobilePro powers off the unit and insures that the backlight is off as well. Tap Start on the Taskbar to access Settings, then select Control Panel. 2. Double tap on the MobilePro Settings icon to launch the dialog box shown in the following figure. Be sure you have the "Power Off" tab selected. Power off settings 3-8 Using the MobilePro 3. Select either to enable suspend mode with battery power or external AC power. VOICE RECORDING Recording voice memos with the MobilePro is easy, even with the unit closed: 1. A short beep will sound indicating that you should begin speaking. Press the Record Button Microphone Recording voice memos 3. You will hear a beep indicating that the voice memo has been saved. 4. To review or edit your voice memos, run the Voice Memo application. Refer to the next section, "Using the Voice Recorder. " Using the MobilePro 3-9 Recording works best if you position the microphone about three inches away from your mouth while speaking. Memory required for voice memo storage varies depending on user settings. Refer to "Using the Voice Recorder" for further details. NOTE Using the Voice Recorder The MobilePro H/PC features a voice recorder application that lets you record and play voice memos. The application features it's own online documentation detailing how to open, play, and edit audio files. PC CARDS Your MobilePro comes with a PC card slot that supports one Type I or one Type II PC card. When using a PC card in the MobilePro, we recommend that you also use AC power. The batteries alone may not provide enough power for some PC cards to operate properly. We recommend using the AC adapter when using PC cards or the internal modem. Using the adapter can help you avoid potential data loss caused by the high-energy consumption of some PC cards. NOTE Inserting PC Cards Follow these procedures to install a PC card. 1. With the PC card facing up, insert it into the PC card slot. 3-10 Using the MobilePro PC Card Inserting a PC card 3. Verify that the PC card is fitted securely into position. ! CAUTION Make sure you align the PC card correctly for insertion. Inserting a PC card incorrectly can damage the card and/or the MobilePro. Using the MobilePro 3-11 Removing PC Cards Remove a PC card from the MobilePro as follows: 1. [. . . ] (Contact the state public utility commission, public service commission or corporation commission for information. ) The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electric device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. In order to program this information into your MobilePro refer to the bFax manual on the CD-ROM. If you are using a different communication software program, refer to its manual. IC CS-03 "NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document. [. . . ]