User manual NEC LCD6520L

[. . . ] User's Manual MultiSync LCD6520L MultiSync LCD6520P (For use in Landscape position only) (For use in Portrait position only) Index Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-2 Warning, Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-2 Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Adjust the screen (See pages 27 and 28) Make adjustments of the screen display position when necessary. 9. Adjust the image (See page 27) Make adjustments such as brightness or contrast when required. 10. Recommended Adjustments To reduce the risk of the "Image Persistence", please adjust the following items based on the application being used: "SCREEN SAVER", "SIDE BORDER COLOR" (See page 30) "DATE & TIME", "SCHEDULE SETTINGS" (See page 28). It is recommended that the "FAN CONTROL" setting (See page 30) be turned to ON also. English-17 English Connections Before making connections: * * First turn off the power of all the attached equipment and make connections. Refer to the user manual included with each separate piece of equipment. NOTE: The LCD6520L and LCD6520P use the same input signal to display images. Content for the LCD6520P should be prepared for use in portrait mode. Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer's screen image. Some video cards and a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. <Factory preset signal timing> Resolution 640 x 480 800 x 600 1024 x 768 1280 x 768 1360 x 768 1280 x 1024 1600 x 1200 1920 x 1080 Scanning frequency Horizontal Vertical 31. 5kHz 60Hz 37. 9kHz 60Hz 48. 4kHz 60Hz 48kHz 60Hz 48kHz 60Hz 64kHz 60Hz 75kHz 60Hz 66. 6kHz 60Hz Remarks Compressed image Recommended resolution Connect the LCD Monitor to a Personal Computer · · · · To connect the VGA IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). To connect the RGB/HV connector (BNC) on the LCD monitor, use a mini D-sub 15 pin to BNC x 5 signal cable (sold separately). When connecting one or more LCD monitors, use the RGB OUT connector (BNC) (BNC INPUT only). To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT button. LCD monitor To RGB/HV IN BNC INPUT only BNC x 5 BNC x 5 LCD monitor (second monitor) BNC x 5 Mini D-sub 15 pin To audio output To analog RGB output Mini D-sub 15 pin PC or IBM compatible English-18 Connecting to a Macintosh Computer Connecting your Macintosh computer to your LCD monitor will enable you to display your computer's screen image. Some video cards or drivers may not display images correctly. Connect the LCD Monitor to Macintosh · · · To connect the VGA IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). To connect the RGB/HV IN connector (BNC) on the LCD monitor, use a mini D-sub 15 pin to BNC x 5 signal cable (sold separately) (BNC INPUT only). If you use with a Macintosh PowerBook, set "Mirroring" to Off. Refer to your Macintosh's owner's manual for more information about your computer's video output requirements and any special identification or configuring your monitor's image and monitor may require. To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT button. LCD monitor To RGB/HV IN BNC INPUT only BNC x 5 BNC x 5 LCD monitor (second monitor) BNC x 5 Mini D-sub 15 pin To audio output To analog RGB output Mini D-sub 15 pin Macintosh English-19 English Connecting with Digital Interface Equipment Connections can be made with equipment that is equipped with a digital interface that complies with the DVI (Digital Visual Interface) standard. Connect the LCD Monitor to a Computer with a Digital Output · · · · · The DVI IN connector also accepts a DVI-D cable. To maintain display quality, use a cable that conforms to DVI standards. To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT button. For mode selection, see "DVI MODE" on page 31. LCD monitor To DVI output DVI-D connector Equipment with a digital interface such as a personal computer with RGB output (TMDS) To audio output DVI-D connector English-20 Connecting a DVD Player with component out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player user's manual for more information. Connect the LCD Monitor to a DVD Player · To connect the DVD/HD IN connector (RCA) on the LCD monitor, use an RCA connector cable (sold separately). Some DVD players may have different connectors such as DVI-D connector. [. . . ] Check to see if volume is set at minimum. Remote Control is not available · Check the Remote Control's batteries status. · · · · Check if batteries are inserted correctly. Check if the Remote Control is pointing at the monitor's remote sensor. The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor, or when there is an object in the path. "SCHEDULE"/"OFF TIMER" function is not working properly · The "SCHEDULE" function will be disabled when the "OFF TIMER" is set. [. . . ]