User manual NEC HT510

[. . . ] Entertainment Projector HT510/HT410 User's Manual English Deutsch Français Italiano Español Svenska IMPORTANT INFORMATION IMPORTANT INFORMATION Safety Cautions Precautions Please read this manual carefully before using your NEC HT510/HT410 Projector and keep the manual handy for future reference. Record it here: CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. [. . . ] Zoom Use the Zoom lever to finely adjust the image size on the screen. E-25 STA TUS POW ER LAM P 3 ON/ STA ND ON/ STA ND BY AUTO ADJ. BY AUTO ADJ. STA TUS POW ER LAM P SELE CT SELE DEO S-VI IN L/mo Cb/P Y O IN VIDE r Cr/PENT IN PON COM PUT COM ER IN AUD IO IN b R AUD IO no IN AC IN CT DEO S-VI IN L/mo Cb/P Y O IN VIDE r Cr/PENT IN PON COM PUT COM ER IN AUD IO IN b R no IN AUD IO AC IN 3. PROJECTING AN IMAGE (BASIC OPERATION) Focus Use the Focus ring to obtain the best focus. NOTE: In a ceiling mounted application, the zoom and focus adjustments may cause the projected image to shift down slightly. If this happens, adjust the lens shift again. Correcting the Vertical Keystone Distortion The Keystone correction feature will correct the vertical distortion of a projected image on the screen. NOTE: Keystone angle can be corrected between 15 degrees upward and 15 degrees downward of projector tilt from level. To correct keystone distortion using the KEYSTONE +/- button: 1. Press the KEYSTONE +/- button once to display the slide bar for adjustment. NOISE RED. Press the KEYSTONE + or - to correct the keystone distortion. HELP VOLUME KEY STONE LIGHT You can also correct keystone distortion by using the menu. Use the SELECT G or H to select "Image" and then "Keystone". NOTE: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment. NOTE: You can save changes by using "Keystone Save" feature when you turn off the projector. PROJECTING AN IMAGE (BASIC OPERATION) Optimizing an RGB Image Automatically Adjusting the Image Using Auto Adjust Optimizing an RGB image automatically Press the AUTO ADJ. button to optimize an RGB image automatically. [Poor picture] Cabinet controls LAMP STATUS POWER Remote control OFF SOURCE POWER ON SELECT COMPONENT COMPUTER VIDEO C-VIDEO COMP. S-VIDEO AUTO ON/STAND BY AUTO ADJ. [Normal picture] Press the AUTO ADJ. button to fine-tune the computer image or to remove any vertical banding that might appear and to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmering). This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This function also adjusts the clock phase to reduce video noise, dot interference or cross talk. (This is evident when part of your image appears to be shimmering. ) This adjustment may be necessary when you connect your computer for the first time. NOTE: · Some signals may not be displayed correctly or take time. · The Auto Adjust function does not work for component and video signals. · If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually. See page E-37. Turning Up or Down Volume Sound level from the speaker can be adjusted. Cabinet controls Remote control PIC-MUTE OFF TIMER FREEZE TIMER MUTE decrease volume LAMP STATUS POWER increase volume increase volume HELP VOLUME KEY STONE LIGHT decrease volume SOURCE SELECT ON/STAND BY AUTO ADJ. NOTE: When no menus appear, the SELECT and buttons on the projector cabinet work as a volume control. E-27 3. PROJECTING AN IMAGE (BASIC OPERATION) Turning off the Projector To turn off the projector: First, press the ON/STAND BY button on the projector cabinet or the POWER OFF button on the remote control. Cabinet controls Remote control OFF LAMP STATUS POWER POWER ON COMPONENT COMPUTER VIDEO SOURCE C-VIDEO COMP. AUTO ADJ. SELECT S-VIDEO ON/STAND BY AUTO ADJ. AUTO MENU Second, press the ENTER button or press the ON/STAND BY or the POWER OFF button again. [. . . ] : Local Contact office : Local Contact office Address : Phone No. , Fax No. on cabinet : Problem of units per User : Required Service : Requested period of Loan unit : Payment method : In Case of Credit Card : Card No. w/Valid Date : (1) Credit Card (2) Travelers Cheque (3) Cash (1) Repair and Return (2) Loan unit E-65 9. APPENDIX Condition of your TravelCare Service Program Enduser is requested to understand following condition of TravelCare Service Program and complete the necessary information on the application sheet. [. . . ]