User manual NEC HIVID 6500

[. . . ] MultiSync Hivid 6500 Projector Large Screen MultiSync Projection System User's Manual Model number: XL-6500/XL-6500G CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. Precautions Please read this manual carefully before using your NEC MultiSync Hivid 6500 Projector and keep the manual handy for future reference. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. [. . . ] Example:If you want to select a signal from the no. 3 slot of the slave Switcher which is connected to the no. 2 slot of the master Switcher, first press the INPUT "2" button, then the INPUT "3" button and then press ENTER. · You can switch to any input signal of NO 01 through10 on the Source Select list by holding down the CTL button and pressing one of the INPUT buttons corresponding to the input number. To activate this function you must first select ENABLE in the Direct Key. · If there are two or more memory locations that contain the same signal information the projector will reference the signal nearest the beginning of the list. To select the next signal use the CURSOR or button and press ENTER. 31 3. OPERATION Source Information Provides and changes information for the parameters of your current projected source. NOTE: For other registered signals, change their parameters on the Source Registry menu. The menu items you can display, change or specify are as follows: Source Name--------------- Changes a user name that has previously been entered. Direct Key ------------------ Assigns settings of source to each INPUT button (1-10) with CTL. Input Slot ------------------- Selects an input terminal for the registered signal when you need to do due to adding optional equipment. Signal System -------------- Displays the signal system of the current source such as RGB, Video, S-Video, or Component signal. Sync System --------------- Selects the detection method of the sync signal. Scale Mode ----------------- Enables or disables to enlarge or reduce the image. To take effect, press and hold CTL then press ZOOM/PAN; to cancel it, do the same again. Input Sig. Size -------------- Specifies the picture size of input signal. Output Sig. Size ------------ Specifies the picture size of output signal. Color Matrix ---------------- Selects the mode to match the output format of an HDTV or DVD signal. CTI Control ----------------- Turns this feature on so you can make the (Color Transient Improvement) color sharper. Noise Reduction ----------- Turns this feature on so video noise can be reduced. Source Select Counter ---- Resets the number of times a signal is selected for display. or button to select the item you want to view or Source Source Direct Input Name Key Slot Mode System System Frequency Polarity Information [ [Not Used A Page1/3 ] ] ] ] [INPUT Display Signal Video Sync Sync [GRAPHICS RGB fH= fV= 15. 74KHz 61. 23Hz VD(+) HD(+) Source Sync Sync Scale Input System Information [Auto Mix Sync [75 [None ] Page2/3 ] Termination Mode Sig. Size Size Scale ] H:1024 H:1024 V:768 V:768 Output Sig. Source Color CTI Matrix Information [Defaul [OFF [OFF 0000 0000H ] ] Page3/3 ] Control Reduction Counter Timer Noise Select Display 00M 32 3. OPERATION The following items can be set: s Source Name To change the source name or input a new source name by selecting one character at a time with the INPUT buttons 1 through 10 and by moving the cursor with the CURSOR button. Only after completely finishing the selection of the characters, press ENTER. [. . . ] To view information, use the CURSOR Topics" menu and press ENTER. s Set Information Lets you know the version for the running time, the lamp usage time, the version for your hardware and software. The information you can view are: User Name ------------------- Indicates the user name Set Serial No. --------------- Indicates serial number for your projector Set hour Meter -------------- Indicates the amount of operating time of your projector Lamp Hour Mete ----------- Indicates the amount of operating time of the lamp Software version ------------ Indicates the version for the software Hardware version ----------- Indicates the version for the hardware *The Switcher item is displayed only when the Connect Condition is set to the SW 1 or 2 Level. NOTE: There is a warning system built-in that displays the following message when you reach 1500 hours of operation "Lamp Running Time is Over 1500 Hours!!" When you see this message please contact your NEC dealer or service personnel for a replacement. [. . . ]