User manual NEC HIVID 3500

[. . . ] MultiSync Hivid 3500 Projector Large Screen MultiSync Projection System User's Manual Model number: XL-3500 CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. Precautions Please read this manual carefully before using your NEC MultiSync Hivid 3500 Projector and keep the manual handy for future reference. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. [. . . ] 30 3. OPERATION NOTE: · While you are viewing a source screen, you can also select the input signal directly by pressing the INPUT "1" through "10" button. In this case INPUT buttons function as follows: When using the projector in stand alone operation: Input Mode Input Module A RGB 1 VIDEO 2 S­VIDEO 3 COMPONENT 4 COMPONENT (HDTV) 5 Slot Selection 10 Numbers designate INPUT buttons on the remote control. When using the projector with the ISS-6020/ISS-6020G: INPUT 1 through 10 Selects the corresponding number slot of the ISS-6020/ISS-6020G When using the projector with two ISS-6020/ISS-6020G or more: To switch to another input signal, enter the master slot number, then the slave slot number by using INPUT buttons and press ENTER. Example:If you want to select a signal from the no. 3 slot of the slave Switcher which is connected to the no. 2 slot of the master Switcher, first press the INPUT "2" button, then the INPUT "3" button and then press ENTER. · You can switch to any input signal of NO 01 through10 on the Source Select list by holding down the CTL button and pressing one of the INPUT buttons corresponding to the input number. To activate this function you must first select ENABLE in the Direct Key. · If there are two or more memory locations that contain the same signal information the projector will reference the signal nearest the beginning of the list. To select the next signal use the CURSOR or button and press ENTER. 31 3. OPERATION Source Information Provides and changes information for the parameters of your current projected source. NOTE: For other registered signals, change their parameters on the Source Registry menu. The menu items you can display, change or specify are as follows: Source Name--------------- Changes a user name that has previously been entered. Direct Key ------------------ Assigns settings of source to each INPUT button (1-10) with CTL. Input Slot ------------------- Selects an input terminal for the registered signal when you need to do due to adding optional equipment. Signal System -------------- Displays the signal system of the current source such as RGB, Video, SVideo, or Component signal. Sync System --------------- Selects the detection method of the sync signal. Color Matrix ---------------- Selects the mode to match the output format of an HDTV or DVD signal. CTI Control ----------------- Turns this feature on so you can make (Color Transient Improvement) the color sharper. Noise Reduction ----------- Turns this feature on so video noise can be reduced. Stadium Mode ------------- Selects this feature so the picture is expanded in the horizontal and vertical directions at different ratios. Source Select Counter ---- Resets the number of times a signal is selected for display. or button to select the item you want to Source Information (List No. 99) Source Direct Input Signal Video Sync Sync Name Key Slot System System Frequency Polarity Page1/2 [NTSC3. 58] [CTL+10 [INPUT A Key ] ] S-VIDEO NTSC3. 58 Cinema fH= fV= 15. 74KHz 61. 23Hz VD(+) HD(+) Source Information (List No. 99) Sync Sync System Termination Mode Page2/2 [Auto ] H/V Separate [Hi-Z ] ] ] Display Color CTL [00:NTSC [Y, B-Y, R-Y [OFF [OFF ] ] ] 00M Matrix Control Reduction Mode Noise Stadium [Normal 0000 0000H Select Counter Display Timer 32 3. OPERATION The following items can be set: s Source Name To change the source name or input a new source name by selecting one character at a time with the INPUT buttons 1 through 10 and by moving the cursor with the CURSOR button. [. . . ] If the remote control loses power, the remote control address becomes "00". In this case the on-screen shown on the right above is not displayed on the screen. 3) To complete, press END. 73 3. OPERATION Help Menu Provides information about operation and adjustment procedures or the set information. To view the information: Press OPERATE or ADJUST button then select "Help" from the Task bar and press ENTER. [. . . ]