User manual NEC DIRECTION SP SERVICE MANUAL

[. . . ] PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Computer Systems Division, Packard Bell NEC, Inc. NEC CSD and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others. The NEC CSD product(s) discussed in this document are warranted in accordance with the terms of the Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon factors such as system configuration, customer data, and operator control. [. . . ] You can select from "Off, " "1, " "2, " "4, " "6, " "8, " "12" or "16 minutes. " A setting of 1 minute achieves maximum power savings, while a setting of 16 minutes allows maximum performance. T Fixed Disk This option controls whether or not a spin down command is issued to the hard drives when the system goes into a low-power mode. Your choices are "Enabled" (default) or "Disabled. " T VESA Video Power Down This option controls power to the monitor during the low-power modes. Your choices are "Disabled" or "Enabled. " Press the right arrow (cursor) key to move to the Boot Menu. Setup Utility 2-15 BOOT MENU The Boot Menu can be used to adjust the system's boot features. The Boot Menu features the following options: T Restore on AC/Power Loss This option specifies whether or not to restore power to the computer if it is turned on and there is a power failure. The options are "Stay Off" which keeps the power off, "Power On" (default) which restores the system's power, and "Last State" which restores the previous power state. T On Modem Ring This option specifies how the system responds when power is off and the modem detects an incoming call. The options are "Stay Off" (default) and "Power On. " T On LAN This option controls how the system responds to a LAN wake-up call. The options are "Stay Off" (default) and "Power On. " T On PME This option controls how the system responds to a PCI power management event. The options are "Stay Off" (default) and "Power On. " T First/Second/Third/Fourth Boot Device You can select the sequence of boot devices by type. Pressing your keyboard's + (plus) or ­ (minus) key allows you to select the order. For maximum system accessibility, Removable Device should always be set as the First Boot Device. Hard Drive Submenu This submenu lists the system's available hard drives. Your computer tries to boot to the operating system on the first device listed on the Hard Drive submenu. If no operating system is found, the system continues trying the drives in the order they are listed until an operating system is located. To see a list of available drives, highlight this field and press Enter. You can select the boot device by pressing your keyboard's + or ­ key. To exit from the Hard Drive submenu, press Esc. 2-16 Setup Utility Removable Drive Submenu This submenu lists any available removable drives (if included). The operating system assigns drive letters to these devices in the order listed. You can change the sequence (and drive lettering) by highlighting this field and pressing Enter. Then press your keyboard's + or ­ key to move a device up or down the list. Press the right arrow (cursor) key to move to the Exit Menu. EXIT MENU The Exit Menu allows you to choose how to exit the Setup program. Press the arrow (cursor) keys to select the desired option, then press Enter to make your choice (or use the arrow key to select another one). T Exit Saving Changes This option exits the Setup program and saves your changes to the BIOS. T Exit Discarding Changes This option exits the Setup program without saving your changes to the BIOS. T Load Setup Defaults This option loads the Setup program's default values. T Load Custom Defaults This option loads Custom default settings. T Save Custom Defaults This option saves your changes to Custom default settings. T Discard Changes This option loads previous values from CMOS RAM for all BIOS settings. NOTE: If your system's CMOS fails, the BIOS will load custom default settings (if you've saved them) or factory default settings. Finally, press Enter again to confirm and exit the Setup program. Section 3 Option Installation This section provides instructions for installing the following options: T expansion boards T DIMM memory upgrade T video upgrade -- see the documentation for your video board T data storage devices T external options. All options (except external options) require the removal of the access cover. [. . . ] Cet appareil numérique de la classe B est conforme àu Règlement sur le brouillage radioélectrique, C. R. C. , ch. 1374. Canadian Department of Communications Modem Connection Requirements NOTE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. [. . . ]