User manual NEC CC MEDIA KIT 2005

[. . . ] Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC LT20 Projector and keep the manual handy for future reference. Record it here: CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. [. . . ] Setting 0 will maximize color reproduction quality. Color Temperature Adjust the color temperature. At higher temperature, the screen looks colder; at lower temperature, the screen looks warmer. Keystone Adjust image distortion caused by tilting projector. (±8 degrees) Aspect Ratio Use this function to choose your desired aspect ratio. 19 . . . English User Controls Image (All) 4:3 : The input source will be scaled to fit the projection-screen. 16:9 : The input source will be scaled to fit the width of the screen. Display Mode There are many factory presets optimized for various types of images. User : Memorize user's settings. Reset Choose "Yes" then "Enter" pressed, the display parameters on this menu will return to their factory default settings. English . . . 20 User Controls Image Computer (Computer mode) Auto Adjust The projector automatically adjusts clock, phase, horizontal and vertical. With most signal sources, Auto Adjust provides the best results. Clock "Clock"changes the display data frequency to match the frequency of your computer's graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. Phase "Phase" synchronizes the signal timing of the display with the graphic card. If you experience an unstable or flickering image, use this function to correct it. Horizontal Position Press the Press the Press the Press the to move the image left. to move the image up. Vertical Position Reset Choose "Yes" then "Enter" pressed, the display parameters on this menu will return to their factory default settings. 21 . . . English User Controls Image Video (Video mode) Color Adjusts a video image from black and white to fully saturated color. Press the to increase the amount of color in the image. Sharpness Adjusts the sharpness of the image. Press the to increase the sharpness. Hue Adjusts the color balance of red and green. Press the to increase the amount of red in the image. Reset Choose "Yes" then "Enter" pressed, the display parameters on this menu will return to their factory default settings. English . . . 22 User Controls Setup Menu Location Choose the menu location on the display screen. Orientation Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen. Remark : The formula is : "ECO mode" lamp hours x 0. 67 = "Normal mode" lamp hours. Lamp Hour Display the cumulative lamp operating time. The lamp hour in OSM is calculated by "Normal mode", when "ECO mode" is selected, the system will convert from "ECO mode" lamp hour to "Normal mode". Signal Type Select signal type RGB or Video sources. Search Signal Lock When this function is turned off, the projector will search for other signals if the current input signal is lost. When this function is turned on, it will search specified connection port. Fan Mode Choose "High" to turn on High Altitude mode. Operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. English User Controls Setup Lamp Mode Choose "ECO" to dim the projector lamp which will lower power consumption and extend the lamp life by up to 150%. Choose "Normal" to return standard mode. Lamp Reminding Choose this function to show or to hide the warning message when the changing lamp message is displayed. [. . . ] NEC SOLUTIONS' LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT NEC SOLUTIONS' OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR RECONDITIONED PRODUCTS, AND REPLACEMENT PARTS MAY BE NEW OR SERVICEABLE USED PARTS. The following are not covered by the limited warranty and NEC Solutions shall not be liable for: 1. or Canada by NEC Solutions or which is not purchased, installed, and operated in the U. S. A or Canada. [. . . ]