User manual NEC 920

[. . . ] TalkTime MaxTM 920 Owner's Manual ATTENTION Before Using the Phone: It is necessary that you CHARGE your phone battery fully before attempting to make or receive a call. Battery Disposal: DO NOT PLACE USED BATTERIES IN YOUR REGULAR TRASH. THIS NICKEL-CADMIUM (Ni-Cd) BATTERY MUST BE COLLECTED, RECYCLED OR DISPOSED OF IN AN ENVIRONMENTALLY SOUND MANNER. Battery Recommendations: The NEC TalkTime MAXTM 920 cellular phone you have purchased was designed to deliver quality performance and provide you with years of use. In order to maintain optimum performance, NEC recommends that only NEC Authentic AccessoriesTM be used with the TalkTime phones. Specifically, NEC recommends only the use of Nickel Cadmium (NiCd) batteries with the TalkTime MAXTM 920 phone. [. . . ] If the key is incorrect, the display will go back to the standby mode. PWR oooo CORRECT FL PWR oooo INCORRECT Note: For security the display will not show the 4-digit lock code. When the lock is cleared the display will go back to the standby mode. If the key is incorrect, the display will remain with the FL indicator on the right side of the display. PWR oooo CORRECT PWR oooo INCORRECT FL When the phone is partially locked, only emergency calls (911) and any numbers stored in memory locations 1 through 9 can be made, but any call can be received. Storing to the memory is also prevented. -12- PARTIAL LOCK 1) Press FCN + I. If you key in the correct code, PL (Partial Lock) will appear on the right side of the display. If the key is incorrect, the display will go back to the standby mode. PWR oooo CORRECT PL PWR oooo INCORRECT Note: For security the display will not show the 4-digit lock code. When the lock is cleared the display will go back to the standby mode. If the key is incorrect, the display will remain with the PL indicator on the right side of the display. PWR oooo CORRECT PWR oooo INCORRECT PL LENGTH OF YOUR CALLS The phone allows you to check the duration of your calls. Upon sending or receiving a call, the current call timer begins counting. PWR CALL-t 01-16 Minutes Seconds Note: The current call timer will be reset upon receipt or sending of another call. -13- RESETTING THE CALL TIMERS Each NAM has a Total Time Counter. The Total Time of all incoming and outgoing calls are registered by these counters. SINGLE - NAM o To View Total Time: Press FCN + 1. PWR totAl-t 003-29 Hours Minutes DUAL - NAM o To Change NAMs: Press FCN + 6. PWR P-1 214 123-4567 PWR P-2 214 234-5678 o To View Total Time: Press FCN + 1. PWR totAl-t 004-15 Hours Minutes RESETTING TOTAL TIME COUNTER To reset the Total Time Counters: o Press FCN + 1+ #. PWR EntEr Cd PWR totAL-t CLEArEd o Press CLR to exit. -14- BACKLIGHTING The phone keypad and display are illuminated to make them easier to read. The backlights come on when you press any key, and go off 10 seconds after your last key press. To turn them on again, simply press another key. SETTING THE RINGING VOLUME The ringing tone sounds when there's an incoming call. If you select level 0, when a call is coming in, the display will flash, the CALL message will appear and flash. USING THE PHONE ON TWO NETWORKS The phone two number capability feature lets you subscribe to both cellular services in your area as well as cellular service in other cities, usually one for each network. [. . . ] -26- TECHNICAL INFORMATION Dimensions Weight Transmitting Power Operating Voltage Frequency Band Standard Battery Capacity Number of Channels Memory Locations Memory Capacity 147. 32x50. 8x27. 94mm (5. 8"x2. 0"x1. 1") 7. 8 ounces 0. 6 W max. battery) 824. 040 - 848. 970 MHz (TX) 869. 040 - 893. 970 MHz (RX) 1000 mAh 832 24 32 digits memory locations 1-24 CARE AND MAINTENANCE Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you enjoy this product for many years. (Water contains minerals that will corrode electronic circuits. ) Avoid all liquid spills. [. . . ]