User manual NEC 42VR5

[. . . ] Operation Manual For the specifications of your plasma monitor, refer to "Model Information". ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANO Important Information Precautions Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference. The manufacturer is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Continued operation at line voltages greater than 100-240 Volts AC will shorten the life of the unit, and might even cause a fire hazard. In case of accident, unplug the power cord and have it serviced by an authorized Service Center. [. . . ] Adjusting the computer image Only the contrast and brightness can be adjusted when a computer signal is connected. Restoring the factory default settings Select "DEFAULT" under the "PICTURE MODE" settings. EXIT RETURN EXIT RETURN Information PICTURE MEMORY Settings OFF: Picture memory not used. Setting the memory · Use the v and w button to select the desired memory place, MEMORY1 to MEMORY6. · Use the and buttons to select "SET", then press the MENU/ENTER button. Resetting the memory Use the v and w button to select the desired memory place, MEMORY1 to MEMORY6, then use the and buttons to select "RESET", and finally press the MENU/ENTER button. The memory is cleared, and "--" is displayed in the "INPUT", "SIGNAL" and "NOTE" columns. Inputting notes · Use the and buttons to select "NOTE", then press the MENU/ENTER button. · When you have finished inputting the note, press the MENU/ENTER button. Reducing noise in the picture Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor. Example: Setting "NR-3" On "NR" of "PICTURE" menu, select "NR-3". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2. 2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. EXIT RETURN G NR : NR-3 Information NR * "NR" stands for Noise Reduction. The effect becomes stronger as the number increases (in the order NR-1 NR-2 NR-3). OFF: Turns the noise reduction function off. E-15 Setting the color temperature Use this procedure to set color tone produced by the plasma display. Example: Setting "HIGH" On "COLOR TEMP. " of "PICTURE" menu, select "HIGH". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : HIGH COLOR TEMP. : 2. 2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. EXIT RETURN Changing the Gamma Curve This feature adjusts the brightness of the midtone areas while keeping shadows and highlights unchanged. Example: Setting "2. 3" On "GAMMA" of "PICTURE" menu, select "2. 3". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2. 3 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. EXIT RETURN G G Information Setting the color temperature LOW: Redder MIDDLE LOW: Slightly red MIDDLE: Standard (slightly bluer) HIGH: Bluer Information GAMMA settings The picture becomes darker as the number increases (in the sequence of 2. 1, 2. 2, 2. 3, 2. 4). * These values are approximate. Adjusting the color to the desired level Use this procedure to adjust the white balance for each color temperature to achieve the desired color quality. Example: Adjusting the "GAIN RED" of "HIGH" color temperature On "COLOR TEMP. " of "PICTURE" menu, select "HIGH", then press the MENU/ENTER button. On "GAIN RED", adjust the white balance. WHITE BALANCE COLOR TEMP. [. . . ] The unit emits a crackling sound. Checks Remedy Picture is disturbed. Monitor's power does not turn on when the remote control's power button is pressed. · Maybe the sound from the cooling fans used to prevent over heating. · If there are no abnormalities in the image and sound, the noise is caused by the cabinet reacting to changes in temperature. · Is a connected component set directly in front or at · Leave some space between the display and the the side of the display? [. . . ]