User manual NAPOLEON GRILLS PTHC38PK

[. . . ] Do not clean the heater with cleaners that are combustible or corrosive. The LP gas cylinder should be turned off when the heater is not in use. WARNING At least once a year, the unit should be inspected for the presence of spiders, spider webs or other insects. The smell of gas in conjunction with extreme yellow colored tips of the burner flames. [. . . ] Fasten the post to the gas cylinder housing using the four (4 pcs) M8 X35mm Bolts , 8mm Lock Washer , Nuts for M8 X35mm Bolts . Step 1 12 5 6 10 8 Step 2 ----Attach Head Assembly to Post Slide the gas hose with the attached Head assembly through the top of the post and down through the hole in the top of the gas cylinder housing. Screw the combustion assembly on to the post, and tighten securely. Step 2 3 5 4 6 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 3 ----Attach Double Pointed Bolt to Head Assembly Attach double pointed bolts (3 pcs) and 6mm washers (3 pcs) to the top of head assembly and tighten the bolts securely. Step 3 9 13 3 Step 4 ---- Attach Center Reflector to Reflector Attach center reflector to the top of reflector (4 pcs) by M6 X 10 mm screws (12 pcs) , 6mm washers (12 pcs) and nuts (12 pcs). Step 4 7 9 1 11 2 7 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 5 ---- Attach Center Reflector and Reflector to the top of Head Assembly Load center reflector and reflector to the top of head assembly by double pointed bolts (3 pcs) 6mm washers (3 pcs) and nuts (3 pcs) Step 5 7 9 13 3 Step 6 ---- Connect Gas Line to Cylinder Attach Gas hose to regulator hose with 3/8 Inch Open End Wrench and Adjustable Wrench. Move cylinder to the plate of base assembly. Step 6 4 15 14 8 SAFETY CHECKS NOTE: Always check the following connections. Check all connections on the hose regulator assembly. Check the hose to the intake pipe to make certain that it is not kinked or in a position that could cause it to kink. The remaining connections are to be tested after this heater has been lit. (SEE LIGHTING INSTRUCTIONS PAGE10) Check for leak Your Patio Heater has been checked at all factory connections for leaks, To check at the Connection at the gas hose/regulator/cylinder. 1) Make leak solution by mixing 1part liquid dishsoap and 3 parts water. 2) Spoon several drops (or use squit bottle) of the solution onto the gas hose/regulator and regulator/cylinder connection. 5) If bubble appear, there is leak, loose and re-tighten this connection. 9 OPERATION WARNING: Do NOT attempt to operate heater until you have read and understand all precaution . Failure to do so can result in serious personal injury, death, or property damage. Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY. Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or liquids. Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. WARNING FOR YOUR SAFETY: If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater. If, after 1 minute, you are unable to light burner, wait 5 minutes and allow flammable vapors to dissipate before attempting to light heater WARNING FOR YOUR SAFETY: Do NOT touch or move heater for at least 45 minutes after use. Allow emitter and dome to cool before touching. Before Lighting Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. There should be at least eight effective times within ten times of ignition. OFF P IL O T LIGHTING INSTRUCTIONS 1)Turn the control knob to "OFF" position. [. . . ] Handle with extreme care. 11 GH LO HI LOCATING HEADER FOR USE BE CAREFUL: WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT UNDER THIS SPACE HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. This heater is primarily used for the heating of outdoor patios, decks, spas, pool and working areas. This heater clearances, shown in Figure 1, must be maintained at all times. The installation must conform to local codes, or in the absence of local codes, with the standard for the storage and handling of liquid petroleum gases, ANSI/NFPA 58-1986, or most recent addition. [. . . ]