User manual NAPOLEON GRILLS PTH10PSS

[. . . ] This appliance must be installed in accordance with such regulations as are in force. Keep the heater away from areas where gasoline or other flammable liquids or vapors are stored. Prior to use, check for damaged parts such as hoses, regulators, pilot or burner. The installation of fixed appliances shall only be carried out by competent persons and be in accordance with the relevant Codes of Practice. [. . . ] All gas connection should be checked for leaks utilising a soap solution. A leak test should be performed with soapy water whenever connecting a new cylinder. If disassembly is required, a leak test should be performed with soapy water upon re-assembly. This heater is designed to operate with a standard 1 LBs propane cylinder with Approved Cylinder Connection. The gas manifold supply pressure must be regulated at 11 inches water column utilising an approved regulator. The minimum inlet gas supply pressure for the purpose of input adjustment is 8 inches water column. LP-gas supply cylinder is not provided with the appliance, statements that (1)the cylinder must be provided with a shut off valve terminating in an LP-gas supply cylinder valve outlet specified, as applicable, for connection No. 510 in the standard for compressed gas cylinder valve outlet and inlet connections, ANSI/CGA-V-I, or connection No. 600 in the compressed gas association's limited standard cylinder valve outlet connection for propane-small valve series. (2)the cylinder supply system must be arranged for vapor withdrawal; (3)the cylinder used must include a collar to protect the cylinder valve. if a connection No. 600 is used a statement that only cylinders marked "propane" must be used. 5 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Step 1 ---- Attach Heater assembly to Base Attach heater assembly to base using 8-32 UNC L=6 (7 pcs) 2 1 10 Step 2 ---- Attach the Burner Column to the Hounsing Insert the clamp (3pcs) of the Burner Column into the spring piece (3 pcs) of Housing per the picture and screw over. Make sure the clamp and the spring piece fit together. 3 2 6 ASSEMBLY Step 3 ---- Attach Emitter Screen to Burner Column. Attach Emitter Screen to Burner Column using 8-32 UNC L=8 (3 pcs) Note: The ignition hole on emitter screen must li ne to the control knob. 3 Ignition Hole 9 3 Step 4 ---- Attach Reflector Dome and Dome Cap and Decorative Dome Cap Nut to Emitter Screen Attach reflector dome to emitter screen of the h eater assembly using 1/4-20 UNC washers (6 pcs) and 11 1/4-20 UNC nuts (3 pcs). Then attach dome cap and decorative dome cap nut to reflector dome. 12 8 7 12 5 7 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Step 5 ---- Attach Emitter Screen shield to Burner Column Attach Emitter Screen shield to Burner Column . Of the heater assembly. 4 4 4 9 3 3 4 Step 6 ---- Connect Gas Hose, Regulator and Cylinder Attach gas hose to regulator. Attach regulator to cylinder. 1. Can connect to ILB portable cylinder dierctly. 20 LB cylinder must binding to a table leg with a provided stretch line. 13 A table leg 8 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Step 7 ---- Check for leak Your Patio Heater has been checked at all factory connections for leaks, To check the Connection of the gas hose/regulator/cylinder. 1) Make leak solution by mixing 1part liquid dish soap and 3 parts water. 2) Spoon several drops (or use squirt bottle) of the solution onto the gas hose/regulator and regulator/cylinder connection. 5) If bubble appear, there is leak, loosen and re-tighten this connection. 13 Step 8---- Disconnect Cylinder When Storing or Transporting 1). Disconnect the cylinder from regulator. 13 Caution: A leak test should be performed with soapy water whenever connecting a new cylinder. If disassembly is required, a leak test should be performed with soapy water upon re-assembly. Never use a match to test for leaks. 9 OPERATION This product is equipped with ODS (Oxygen Deprivation System) WARNING: DO NOT attempt to operate heater until you have read and understand all precautions. Failure to do so can result in serious personal injury, death or property damage. Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY. [. . . ] Allow all burner elements to cool before touching. FOR YOUR SAFETY : NOTE In a salt-air environment (such as near an ocean). Frequently check for corroded areas and repair them promptly. STORAGE : Between uses: Turn the control knob to "OFF" position. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, cover heater to protect exterior surfaces and to help prevent debris in air passages. [. . . ]