User manual NAPOLEON GRILLS BICSS610RB

[. . . ] SERIAL #______________________ BUILT-IN CSS610RB INSTRUCTION GUIDE Please use this manual in conjuction with your main manual to properly assemble your built-in grill. Refer to the main manual for operating, cleaning, and maintenance instructions. This grill is designed for masonry, noncombustible enclosures only, and must be installed and serviced by a qualified installer to local codes. BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as shown in the built-in instructions. [. . . ] Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223. 1 in the United States. Built in units are supplied with a drip pan which holds only a minimal amount of grease. Access must be provided to the inside of the enclosure to make gas connections. 32" 6" MIN 9 ¾" 20 ¼" 2" 2 ½" 34" RECOMMENDED GAS INLET OPENING N415-0147 / JAN 12/06 BUILT-IN ACCESSORY OPENING DIMENSIONS D NOTE: ACCESSORY FRAMES OVERLAP OPENING BY 1 ½" ON ALL 4 SIDES H W Part # Description Picture OPENING DIMENSION W H 18 ¼" D N370-0069 Flat vertical painted door 13 ¼" N370-0071 Flat vertical stainless steel door 13 ¼" 18 ¼" N370-0070 Flat horizontal painted door 18 ¼" 13 ¼" N370-0072 Flat horizontal stainless steel door 18 ¼" 13 ¼" N370-0356SS Curved stainless steel door - 308 size 22 ½" 19 ¾" N370-0357SS Curved stainless steel door - 450 size 27" 19 ¾" N370-0358SS Curved stainless steel double door - 600 size 35 ¼" 19" N370-0361 PF style stainless steel door 17" 23 ¼" N370-0359 PF style stainless steel single drawer 17 ¼" 6 ¾" 23" N370-0360 PF style stainless steel triple drawer 17 ¼" 22 ¾" 23" GAS INLET OPENING 1. Feed the gas flex connector and regulator down through the opening on the left hand side (natural gas only). For propane units, connect the gas supply to the 3/8" flare fitting located on the left side of the manifold tube. Leak test the entire installation before operating the unit. BUILT-IN ACCESSORY DRAWER INSTRUCTIONS 1. Remove the drawers from the enclosure by fully extending them and then lifting up to remove them from the slides. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located at the same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to ensure that the front of the enclosure is plumb. Re-install the drawers by tipping the back of the drawer down into the slide. Once the wheels are inserted into the slide, lower the front of the drawer until it is level, then push in. Note: if the enclosure is installed with shims that are too thick, the wheel will not engage into the slide. Remove the protective coating from all remaining surfaces. BUILT-IN ACCESSORY DOOR INSTRUCTIONS 1. For the curved stainless steel doors, remove the door(s) from the frame by lifting the door while holding on to the pivot rod. This will allow the pivot rod to come out of the hole on the bottom of the frame. [. . . ] Other than on the curved stainless steel double door kit, fasteners are not required on the top and bottom of the frame. The curved stainless steel double door frame must be fastened in the center both at the top and bottom. Once the frame has been secured and checked for squareness, the door can be re-installed. [. . . ]