User manual NAIM1 CD555 PLAYER MANUAL

[. . . ] owners manuaL CD PLaYers enGLIsH DeuTsCH FranÇaIs ITaLIan0 Cont ent s Page section saFeTY InsTruCTIons In order to comply with current european safety regulations it is essential that the naim loudspeaker connectors supplied with amplifiers and loudspeakers are used. Do not under any circumstances allow anyone to modify your naim equipment without first checking with the factory, your retailer, or your distributor. equipment must not be exposed to dripping or splashing and no objects filled with liquid, such as vases, should be placed on the equipment. For your own safety do not under any circumstances open naim equipment without first disconnecting it from the mains. [. . . ] The player must not be inverted either during or after transit screw removal. 8 CDs 3 Con necti o ns 8. 1 rear P anel Power supply input (XPS or CD 555PS) DIN output Comms interface RC5 input note: RCA phono and DIN output sockets should not be connected simultaneously. note: The RC5 Input is intended to accept external control signals for multi-room applications. note: The optional RJ45 socket Comms Interface can provide external control of the player in custom installations. Contact your dealer or Naim Audio directly for further information. RCA phono output left RCA phono output right CDs3 DIn output ch1 ch2 -ve nc nc e7 C D S3 8. 2 CDs3 Connected to XPs Power supply Mains input and fuse CD Burndy Cable note: If a CD 555PS Power Supply is used to power a CDS3 player use only power supply output Socket 1. 1 D isc Loading To load a compact disc lift the transport lid from the front of the player. note: If an HDCD® encoded compact disc is loaded the CDS3 will automatically recognise and decode it. The display will read HDCD for a few seconds after play is pressed. 9 . 2 P l a y er m a i n t en a n ce It is important for reliable operation of the CDS3 to ensure that the surfaces of the transport platter and the underside of the puck are free of dust or debris which can prevent the disc from sitting properly and cause it to slip. To clean the transport platter, take a piece of Blu-Tack and lightly apply it to the top surface of the magnetic metal hub, picking up any material attached to it. Brush the plastic outer edge lightly with your finger or a soft brush to ensure that it is dust and particle free. Similarly, clean the puck with Blu-Tack, to remove debris from the three locating pins on its underside. Do not, under any circumstances, use any solvents or fluids for the cleaning process. e8 CDX2 1 0 CDX2 In t rod ucti o n a nd Instal l a ti on The CDX2 CD Player can be operated either from its internal power supply or, for improved performance, from an external naim CD 555Ps or XPs Power supply. CD player control and operation is described in sections 19, 20 and 21. The CDX2 should be installed on a dedicated equipment stand intended for the purpose. To improve sound quality the player has hard metallic feet which may blemish any delicate surface on which it is placed. Do not stand the player directly on top of another item of naim audio equipment. The CDX2 is fitted with both analogue and S/PDIF digital output options selectable using a rear panel switch. a transit screw on the underside of the CDX2 should be removed before use and must be replaced if the unit is to be moved or re-packed and shipped. The player (and external power supply if used) should be installed in its final location before connecting cables or switching on. ensure that power amplifiers are switched off and the preamplifier volume is turned down before the player (or external power supply) is switched on. The player and power supply are heavy and care should be taken when lifting or moving them. [. . . ] Selects the next source input. note: Preamplifier or integrated amplifier program mode can be selected from the R-com by pressing and holding the pre key. Program mode functions can then be accessed from the equipment front panel. e15 N A R C O M 4 H a ndset 2 1 nar Co m 4 H a nd set The narCom 4 is a multi-functional remote control handset designed to be used with naim audio CD players, integrated amplifiers, preamplifiers, preset tuners and subwoofers. To fit batteries, remove the battery cover and insert the batteries into the body taking care with their orientation. replace the battery cover. 21. 1 using n arC o m Operation of the NARCOM handset is based around three types of keys: system Component Keys, Global Keys and soft Keys. [. . . ]