User manual NAD T761

[. . . ] NAD GB · OWNER'S MANUAL ©2001 NAD ELECTRONICS LTD. T 761 T 761 IMPORTANT SAFETY INSTRUCTIONS CAUTION ATTENTION: RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Warning: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. ATTENTION POUR ÉVITER LES CHOC ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. [. . . ] If no digital audio signal is detected, "DIGITAL 1" indicator will blink. The Video 1 input will also select the Component Video input; the signal will be routed to the Component Video output sockets. VIDEO 2 Video 2 selects the signal from a TV/Satellite/Cable receiver or DVD player connected to VIDEO 2 as the active input. "VIDEO-2" is shown in the Display Panel when selected. 11. HEADPHONE SOCKET & VIDEO 5 INPUT HEADPHONE SOCKET A 1/4" stereo jack socket is supplied for headphone listening and will work with conventional headphones of any impedance. Use a suitable adapter to connect headphones with other types of connectors such as 3. 5mm stereo `personal stereo' jack plugs. De-select Speakers A and/or B to mute the loudspeakers for private listening. NOTES: In the OSD menu "Speaker settings" be sure to have selected and adjusted a preset with "MAIN SPEAKERS" set to "LARGE". Refer also to Chapter "On Screen Display (OSD)" for more information. VIDEO 5 INPUT For easy and temporary connection you can connect a camcorder (playback only) or video game console. If the game console or camcorder is mono, connect the audio lead to the R (Right) audio socket. 12. SPEAKERS A & B Pressing the Speakers A button will disengage the main loudspeaker system (the Front A, Center and Surround speakers). Press the button again to switch the speakers back on. NAD 14 GB The Digital Input 2 is linked to the Video 2 Input (marked Digital In 2 on back panel; No. Digital Input 2 allows for connection of a digital source with an Optical digital output. Whenever the corresponding digital input is activated, Digital Input 2 will also be selected; in the display the "DIGITAL 2" indicator will start to blink. If a digital audio signal is detected, the "DIGITAL 2" indicator will stop blinking and remain lit. If no digital audio signal is detected, "DIGITAL 2" indicator will blink. VIDEO 3 & VIDEO 4 Video 3 & 4 select the signal from a TV/Satellite/Cable receiver, DVD player or VCR connected to VIDEO 3 or VIDEO 4 as the active input. "VIDEO-3" or "VIDEO-4" is shown in the Display Panel when selected. The Video 3 & 4 inputs also have video and analogue audio outputs specifically for recording video devices. The Digital Input 3 and 4 are linked respectively to the Video 3 & 4 input (marked Digital In on back panel; No. Digital Inputs 3 & 4 allows for connection of a digital source with a Coaxial digital output. [. . . ] The T 761 can delay the center channel output up to 5 milliseconds and thus compensates for center channel speakers that are up to 5 feet (1. 5 m) closer to the listening position than the front left and right speakers. NOTES: In rare system setups, the center channel speaker is actually further away than the front left and right speakers. The center channel delay time adjustment is only available in Dolby Digital surround mode. To set the rear channel delay time, · Use the 3 or 4 cursor button (No. [. . . ]