User manual NAD T742

[. . . ] ® AV Surround Sound Receiver Owner's Manual ENGLISH T742 IMPORTANT SAFETY INSTRUCTIONS CAUTION ATTENTION: RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Warning: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. [. . . ] Press the Down/Up button again for 1/2 second to start searching again. The control is also used to adjust various set-up settings and levels for the T742. 17) the speakers size and delay can be adjusted; in conjunction with the Tone Control button (No. Refer also to sections "SETUP" and "Tone controls" in this chapter. HEADPHONE SOCKET & VIDEO 5 INPUT HEADPHONE SOCKET - A 1/4" stereo jack socket is supplied for headphone listening and will work with conventional headphones of any impedance. Use a suitable adapter to connect headphones with other types of connectors such as 3. 5mm stereo `personal stereo' jack plugs. Inserting a headphone will automatically turn off all speakers and signals from the Audio Pre-Out sockets and switches the T742 to the stereo mode. Surround sound modes are not available when headphones are inserted in the headphone socket. NOTES · In the VFL display "Speaker settings", be sure to have selected and adjusted a preset with "MAIN SPEAKERS" set to "LARGE". VIDEO 5 INPUT - For easy and temporary connection you can connect a camcorder (playback only) or video game console. If the game console or camcorder is mono, connect the audio lead to the R (Right) audio socket. AUDIO & VIDEO INPUT SELECTORS DVD & SAT - DVD & SAT selects the signal from a TV/Satellite/Cable receiver or DVD player connected to DVD or SAT as the active input. "DVD" or "SAT" is shown in the Display Panel when selected. The Digital Input DVD or SAT is linked to the DVD or SAT input (marked DVD & SAT on back panel; No. Digital Input DVD or SAT allow for connection of a digital source with an Optical (Toslink) digital output. Whenever the corresponding digital input is activated, Digital Input DVD or SAT will also be selected; in the display the "DVD" or "SAT" indicator will start to blink. If a digital audio signal is detected, the "DVD" or "SAT" indicator will stopblinking iand remain lit. If no digital audio signal is detected, "DVD" or "SAT" indicator will cease blinking and extinguish. VCR & VIDEO 4 - VCR & 4 select the signal from a TV/Satellite/Cable receiver, DVD player or VCR connected to VCR or VIDEO 4 as the active input. "VCR" or "VIDEO-4" is shown in the Display Panel when selected. The VCR & 4 inputs also have video and analogue audio outputs specifically for recording video devices. The Digital Input VCR is linked to the VCR input (marked Digital In on back panel; No. Digital Input VCR allows for connection of a digital source with a Coaxial (RCA Jack) digital output. [. . . ] Pressing the TEST button engages the Test signal generator to allow for adjustment of all speaker levels, so that each channel can be adjusted for equal loudness at your listening position. The test signal scrolls automatically with 2 second intervals from Left, Centre, Right, Rear Right, Rear Left, to sub-woofer in continuous cycles. If an adjustment in set-ting is made for one of the speakers, scrolling will stop until 2 seconds after the adjustment was made. The display panel shows which speaker is being fed with the test signal. [. . . ]