User manual NAD M50

[. . . ] ® Owner’s Manual Digital Music Player M50 РУССКИЙ SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ SAVE THESE INSTRUCTIONS FOR LATER USE. 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference. 3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. [. . . ] Put all your music files in this “Music” folder, connect it to M50’s USB 2 and then re-index – this “Music” folder is now your “Library” where all songs are stored or ripped. 6 ETHERNET/LAN LAN connection must be setup for wired connection to be established. Set up a Wired Ethernet broadband router with broadband internet connection. Your router or home network should have a built-in DHCP server to consummate the connection. • Using a standard straight-through Ethernet cable (not supplied), connect one end of the Ethernet cable to the LAN port of your wired Ethernet broadband router and the other end to M50’s LAN port. 7 RS232 Use a RS232 serial cable (not supplied) with RS232 adapter (if necessary) to interface this port to the corresponding RS232 connector of the optional M2, M51, C390DD or any compatible NAD models. Through this RS232 connection, the VOLUME slider in the App can be adjusted to increase or decrease the audio output level of the M50. 8 IR IN, IR OUT These mini-jacks accept and output remote-controlled codes in electrical format, using industry-standard protocols, for use with “IRrepeater” and multi-room systems and related technologies. • All NAD products with IR IN/IR OUT features are fully compatible with M50. For non-NAD models, please check with your other product’s service specialists as to their compatibility to the M50’s IR features. IR IN This input is connected to the output of an IR (infrared) repeater (Xantech or similar) or the IR output of another compatible device to allow control of the M50 from a remote location. Command and control the linked compatible device by directing its own remote control to M50’s infrared receiver. 9 +12V TRIGGER IN With this input triggered by a 12V DC supply, the M50 can be switched ON remotely from standby mode by compatible devices such as amplifiers, preamplifiers, receivers, etc. • Connect this +12V trigger input to the remote device’s corresponding +12V DC output jack using a mono cable with 3. 5mm male plug. • The controlling device must be equipped with a +12V trigger output to use this feature. +12V TRIGGER OUT • The +12V TRIGGER OUT is used for controlling external device that is equipped with a +12V trigger input. • Use a 3. 5mm mini-jack connector to pass +12V to a compatible device equipped with +12V TRIGGER IN. · This output will be 12V when the M50 is ON and 0V when the unit is either OFF or in standby mode. 10 IDENTIFICATION OF CONTROLS 10 WIRELESS (WIFI) ANTENNA TERMINAL • Install the supplied wireless antenna into this wireless antenna terminal (WiFi). • For wireless connection to be established, ensure that the supplied wireless antenna is installed and Wireless (WiFi) broadband router with broadband internet connection is setup and available. • When the POWER switch is set to ON position, the M50 goes to standby mode as shown by the amber status condition of the Standby LED. Press the front panel Standby button or remote control’s [ON] button to switch ON the M50 from standby mode. • If you intend not to use the M50 for long periods of time (such as when on vacation), switch off the POWER switch. • With POWER switched off, neither the front panel Standby button nor remote control’s [ON] button can activate the M50. 12 FUSE HOLDER Only NAD service personnel can access the fuse holder in the unlikely event a fuse may need to be replaced. [. . . ] Several suggested stations, shows, songs or broadcasts corresponding to your search will be shown. 3 Select from the suggested list the station, show, song or broadcast you were looking for. Otherwise, try searching again. SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH OPERATION ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ DISPLAY OF CURRENT BROADCAST When a particular radio station is being broadcast, a small thumbnail image of the radio station logo is shown at the lower left corner of the screen display. Select this thumbnail image. When TuneIn icon is selected, among the options that appear is the “Report problem”. [. . . ]