User manual NAD L56

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated `dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. To ensure proper use of this product, please read this owner's manual carefully and retain for future reference. Should the unit require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in exposure to laser radiation. [. . . ] LOADING CODE-LIBRARIES The HTR L76 can store a different library of default NAD codes for each of its Device Selector "pages. " If the original default library does not control your NAD CD player, tape deck, DVD player, or other component, follow the procedure below to change the code-library. Begin by ensuring that the component you wish the HTR L76 to control is plugged in and powered-up ("on, " not merely in standby). To enter the HTR L76's Library Mode, simultaneously press-and-hold for 3 seconds both the desired Device Selector key and the "PROGRAM" key, until the Learn LED turns green. While keeping the HTR L76 pointed toward the component, enter the first appropriate three-digit codelibrary number from the table below. If the component turns off, press "ENTER" to accept that codelibrary number and exit the Library Mode. If the component does not turn off, enter the next three-digit code-library number from the table. When you enter the correct number the component will turn off; press "ENTER" to accept that code-library number and exit the Library Mode. SEARCH MODE If none of the codes from the table turn off the component, and if you are quite sure you have followed the above procedure completely and carefully, you may want to try the "search" method as follows: Enter Library Mode by simultaneously pressing-and-holding for 3 seconds both the desired Device Selector key and the "PROGRAM" key, until the Learn LED turns green. Now press-and-hold the HTR L76's or key; the remote will step through all the available codes at a rate of approximately 1 per second. When the component turns off, immediately release the cursor key; press "ENTER" to accept that codelibrary and exit the Library Mode. Try a few commands; should you prove to have stepped past the needed code-library, re-enter the Library Mode and use the cursor key to step back to it. NOTE It is possible that search mode will find code-libraries that operate, at least partially, some other-brand (non-NAD) components. However, since we can only ensure the completeness or accuracy of NAD code-libraries, we cannot support the HTR L76's operation with other-brand components. CHECKING CODE-LIBRARY NUMBER You can check the current code-library on any Device Selector key as follows. Enter Library Mode by simultaneously pressing-and-holding for 3 seconds both the desired component's Device Selector key and the "PROGRAM" key, until the Learn LED turns green. press the "DISP" key; the HTR L76 indicates the current code-library by flashing its "TAPE" , "VCR" , and "MACRO" keys. For example, to indicate codelibrary #501 the HTR L76 will flash "TAPE" 5 times, pause, and then flash "MACRO" once. You might wish to make a note of your components' code-library numbers. When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections. If you connect the DVD player to a VCR, the playback picture will be distorted because DVD video discs are copy protected. ⷠTo connect with S-video or SCART VIDEO (Component Video), you have to select TV output mode properly (Refer to "selecting TV Output" on Page 35). [. . . ] DOLBY DIGITAL/PCM Select "DOLBY DIGITAL/PCM"if an active digital output is supplied to the Dolby Digital decoder, (or an amplifier or other equipment with a Dolby Digital decoder). STREAM/PCM Select "Stream/PCM" if an active digital output is supplied to an amplifier or other equipment with DTS decoder, Dolby Digital decoder and MPEG decoder. PCM Select "PCM" if an active digital output is supplied to an amplifier or other equipment with linear PCM only (or MD recorder or DAT deck). nOTES · When you are not using the player's digital audio output, don't select any of the options. [. . . ]