User manual NAD C370

[. . . ] Warning: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. the exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Do not place this unit on an unstable cart, stand or tripod, bracket or table. [. . . ] 2) over the power button will light up amber and after a short pause will turn to green to indicate the amplifier is now ready for normal operation. Pressing the POWER switch again will turn the unit OFF completely, it will not respond to the remote control. 1) When the amplifier is switched On, pressing the green On/Off button on the remote handset will put the NAD-370 into Standby mode and the Power indicator will turn amber. The amber Power indicator shows that power is being supplied to the NAD-370, but the system is currently in the Standby Mode. This can be particularly useful to keep components within a system "insync": This way all components will switch to stand-by when Off is pressed or switch to operating mode when On is pressed, instead of some components switching On when the amplifier is switched to Stand-by. 2) will turn from amber to green and the indicator for the last selected input will blink and light up. Press the OFF button to switch the unit to the Stand-by mode: The Stand-by indicator will light up amber. However, it is recommended that you switch the unit totally off if it is not going to be used for more than a couple of days. Switch off completely by pressing the POWER button on the front panel (No. STAND-BY/PROTECTION INDICATOR Upon switching Power on, the indicator will light up red and after a short pause turn to green to indicate the amplifier is ready for use. In cases of serious abuse of the amplifier, such as overheating, excessively low loudspeaker impedance, short circuit, etc. In such a case, turn the amplifier off, wait for it to cool down and/or check the speaker connections, making sure the overall loudspeaker impedance doesn't go below 4 ohms or 8 ohms in Bridge Mode. HEADPHONE SOCKET A 1/4" stereo jack socket is supplied for headphone listening and will work with conventional headphones of any impedance. Use a suitable adapter to connect headphones with other types of sockets, such as 3. NOTE: Make certain that the volume control is turned to minimum (fully counter-clockwise) before connecting or disconnecting headphones. If Speakers A and B are both engaged (both indicators over the Speakers A and B buttons are lit), the amplifier's output power is fed to both sets of speakers in parallel. If speakers A and B are disengaged, both sets of speakers are silenced. NOTES: Always turn the volume down when engaging or disengaging either Speaker A or Speaker B. When using Speakers A and B at the same time, make sure that the total impedance of the speakers connected is more than 8 ohms. Direct sunlight, very bright or fluorescent ambient lighting may affect the operating range and angle for the remote control handset. SOFT CLIPPINGTM INDICATOR The green SOFT CLIPPINGTM indicator shows that the Soft ClippingTM mode is engaged. BASS & TREBLE CONTROLS The NAD C370 is fitted with BASS and TREBLE tone controls to adjust the tonal balance of your system. [. . . ] Use los conectores de Speaker A para los altavoces `principales' y use los conectores de Speaker B para un segundo par, por ejemplo, altavoces de extensión colocados en otra habitación. Anslut högtalare till högtalarkontakterna och signalkällorna till respektive ingångskontakt. Anslut en kabel från TAPE 2 OUT på C 370 till däckets LINE IN kontakter, och en andra kabel till däckets LINE OUT kontakter till TAPE 2 IN kontakter. Anslut en kabel från TAPE 1 OUT på C 370 till däckets LINE IN kontakter, och en andra kabel till däckets LINE OUT kontakter till TAPE 1 IN kontakter. [. . . ]