User manual NAD C352

[. . . ] 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference. 3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4 Follow Instructions - All operating and use instructions should be followed. [. . . ] BARE WIRES AND PIN CONNECTORS Bare wires and pin sockets should be inserted into the hole in the shaft of the terminal. Unscrew the speaker terminal's plastic bushing until the hole in the screw shaft is revealed. Insert the pin or bare cable end into the hole and secure the cable by tightening down the terminal's bushing. Ensure bare wire from the speaker cables does not touch the back panel or another socket. Ensure that there is only 1/2" (1cm) of bare cable or pin and no loose strands of speakers wire. SOFT CLIPPINGTM When an amplifier is driven beyond its specified power output, a hard, distorted sound can be heard on very loud sounds. This is caused by the amplifier cutting off or 'hard clipping' the peaks of sound that it was not designed to reproduce. the NAD Soft ClippingTM circuit gently limits the output of the system to minimise audible distortion if the amplifier is overdriven. If your listening involves moderate power levels you may leave the Soft ClippingTM switch to Off. If you are likely to play at high levels, that could stretch the amplifier's power capability, then switch Soft Clipping On. The Soft ClippingTM indicator on the front panel will illuminate when the amplifier is in Soft Clipping mode. 12V TRIGGER OUT This output allows to remotely switch on or off ancillary equipment such as a tuner, power amplifier, etc. This can also be an AC outlet power strip equipped with a 12V trigger input. The 12V trigger output is activated whenever the unit is switched to normal operational mode from Stand-by or Off. Failure to observe the above may result in damage to the C 352 or any ancillary components attached to it. If in doubt over the connections, installation and operation of the 12V trigger output consult your NAD dealer. IEC AC MAINS (POWER) INPUT The C 352 comes supplied with a separate AC Mains cable. Before connecting the cable to a live wall socket ensure that it is firmly connected to the NAD C 352's AC Mains input socket first. Always disconnect the AC Mains cable plug from the live wall socket first, before disconnecting the cable from the C 352 Mains input socket. SWITCHED AC OUTLET (NORTH AMERICAN VERSIONS ONLY) The AC power cord of another component may be plugged into this accessory outlet. Components plugged into this outlet will be switched On and Off by the POWER button on the front panel or by the ON and STAND-BY button on the remote control handset. NOTE: The total power consumption of any components connected to the AC outlets may not exceed 100 Watts. [. . . ] For the latest information about your C 352, updated documentation and features please log onto www. Batteries flat, or incorrectly inserted IR transmitter or receiver windows obstructed IR receiver in direct sun or very bright ambient light Check or replace batteries Remove obstruction Place unit away from direct sun, reduce amount of ambient light Överbelasta inte vägguttag och förlängningssladdar då det kan ge upphov till elektriska överslag och risk för stötar. Door nogmaals op de aan-/uit-schakelaar te drukken, wordt de unit volledig UITgeschakeld, en reageert de unit niet meer op de afstandsbediening. Oorzaak Netsnoer niet aangesloten of unit niet ingeschakeld Tape 1 Monitor geselecteerd Mute ingeschakeld Achterste Pre Out/ Main in versterkerverbindingen niet aangebracht Geen luidsprekers geselecteerd Balansregeling niet in midden Luidspreker niet correct aangesloten of beschadigd Ingangskabel ontkoppeld of beschadigd Luidspreker niet in fase aangesloten · Överbelasta inte vägguttag och förlängningssladdar då det kan ge upphov till elektriska överslag och risk för stötar. [. . . ]