User manual NAD C160

[. . . ] Do not use this unit near water; for example, near a bath tub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. The unit should be installed so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet, that may impede the flow of air through its ventilation openings. The unit should be situated from heat sources such as radiators, heat registers, stoves or other devices (including amplifiers) that produce heat. [. . . ] Using twin RCA-to-RCA leads, connect to the left and right `Audio Output' of the tape machine to the TAPE 2 IN sockets for playback and tape monitoring. Using twin RCA-to-RCA leads, connect to the left and right `Audio Output' of the tape machine to the TAPE 1 IN sockets for playback and tape monitoring. Connect the twin RCA lead from your turntable to this input if you are using a Moving Magnet cartridge. PHONO GROUND CONNECTOR Often, the twin RCA leads from turntables also includes a single wire earth lead. Use a twin RCAto-RCA lead to connect the CD player's left and right `Audio Outputs' to this input. The output level can be reduced by up to 12dB; when set to the maximum position (at the 0dB position), the output level will be identical to that of the PRE OUT 1 sockets. NOTE: always turn the pre-amplifier and associated power amplifiers off before connecting or disconnecting anything to the Pre-Out 1 & 2 sockets. NAD LINK IN, OUT The NAD-Link connector is used to pass commands from other units fitted with NAD-Link connectors. This allows centralised control of a complete system, and also allows some of the basic functions of other NAD components (such as a CD player or cassette-deck) also equipped with NAD-Link to be controlled with the pre-amplifier's remote control. To function with such other units, connect the C160's NAD-Link Out to the NAD-Link In on the other unit. NAD-Link connectors can be daisy-chained, IN to OUT, so that a whole system can be controlled from the remote control facilities of one unit. 12V TRIGGER OUT The 12V trigger is activated automatically when switching the NAD C160 from off or stand-by to on. Connect the 12V trigger to a power amplifier or AC outlet power strip equipped with a 12V trigger input for remote on/off switching of those devices. SWITCHED AND UNSWITCHED POWER OUTLETS (AH VERSION ONLY) The AC power cords of other stereo components, such as a CD player, may be plugged into these accessory outlets. Components plugged into the outlet marked "switched" will be switched on and off as the pre-amplifier is switched from stand-by or off to on and vice versa. Mains power is always available on the outlet marked "unswitched" as long as the NAD C160's power cord is plugged into a live AC wall outlet. This outlet can be used for components which may require continuous supply of AC mains; some tuners require uninterrupted mains supply to retain preset memory, for instance. NOTE: The total power consumption of any components connected to the AC outlets may not exceed 100 Watts. Never connect the mains lead of a power amplifier to either the Switched or Unswitched outlets of the NAD C160. On the front panel, press any of the input selector buttons to switch to pre-amplifier on. From the remote control, press the green Stand-by button (located just over the Speakers A and B buttons) to switch the unit on. The Stand-by indicator will turn from amber to green to indicate it is switched on and ready for use. [. . . ] 13) to reduce the output level of PRE OUT 2 so that the volume level of both power amplifiers is exactly matched. Power AC lead unplugged or power not switched on · Power amplifier is switched off · RCA lead to power amplifier not properly connected or damaged. IR receiver in direct sun or very bright ambient light Solution · Check if AC lead is plugged in and power switched on · Place unit away from direct sun, reduce amount of ambient ligh Anslut en kabel från TAPE 2 OUT på C160 till däckets LINE IN kontakter, och en andra kabel till däckets LINE OUT kontakter till TAPE 2 IN kontakter. Anslut en kabel från TAPE 1 OUT på 160 till däckets LINE IN kontakter, och en andra kabel till däckets LINE OUT kontakter till TAPE 1 IN kontakter. [. . . ]