User manual NAD C 725BEE

[. . . ] ® Owner’s Manual Stereo Receiver C 725BEE РУССКИЙ SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ Save these instructions for later use. 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference. 3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. [. . . ] However, for critical listening and to preserve optimum dynamics, you may wish to defeat it by setting this switch OFF. 14 POWER SWITCH: The POWER switch supplies the master AC mains power for the C 725BEE. When this switch is at ON position, the C 725BEE is in standby mode as shown by the amber status condition of the standby LED. If you intend not to use the C 725BEE for long periods of time (such as when on vacation), switch the POWER switch to the OFF position. When the POWER switch is at OFF position, the front panel power button, SR 8 remote control or ZR 5 cannot activate the C 725BEE. 15 SWITCHED AC OUTLET: This convenience outlet can supply switched power to another component or accessory. With the Power switch at the rear panel set to ON position, this outlet is powered ON or OFF by the front panel STANDBY switch or by the SR 8’s [ON/OFF] buttons. The total draw of all devices connected to this outlet must not exceed 120 watts for 120V version and 115 watts for 230V version. 16 RS-232: Connect this interface via RS-232 serial cable (not supplied) to any Windows® compatible PC to allow remote control of the C 725BEE through NAD’s proprietary PC software or other compatible external controllers. NAD is a certified partner of AMX and Crestron and fully supports these external devices. 17 MP DOCK: The C 725BEE is equipped with a data port in the rear panel where an optional “NAD IPD 1 Dock with iPod” (NAD IPD 1) can be plugged in. Connect the “MP DOCK (DATA PORT)” jack of the C 725BEE to the corresponding “DATA PORT” socket of the optional NAD IPD 1. Refer also to LISTENING TO YOUR iPod PLAYER under the OPERATION main heading. NOTE C 725BEE is compatible with NAD IPD 1 and later NAD IPD variants. Check with your dealer or NAD audio specialist for other versions of NAD IPD compatible with C 725BEE. 18 FM ANTENNA INPUT: The supplied wire “dipole” FM antenna will connect to the FM connector using the supplied “balun” adapter. It will usually work best when mounted on a vertical surface such as a wall, with arms fully outstretched forming a horizontal “T” perpendicular to the origin point of the signal. Refer also to the item ABOUT ANTENNAS at the LISTENING TO AM/FM RADIO section of the OPERATION page. 19 AM ANTENNA INPUT: Connect the supplied AM loop antenna to these terminals. If an external AM antenna is used, make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna. Refer also to the item ABOUT ANTENNAS at the LISTENING TO AM/FM RADIO section of the OPERATION page. 20 DAB MODULE INPUT PORT (230V version only): Plug-in the other end of the Mini-Din connector from the NAD DAB Adaptor DB 1 module output port into this socket. [. . . ] Dock your iPod player into the NAD IPD 1 - “iPod Connected” will be displayed in the lower line of the VFD. SKIP [ ] Press [ ] to skip forward to the next song or skip back to the previous song. RPT (REPEAT) Toggle to playback repeatedly a particular song or repeat all songs in a list. DISP (DISPLAY) If the iPod’s display screen is dim, press [DISP] to turn ON the backlight and illuminate the display screen. NOTE For other navigation functions, please refer to your iPod player’s owner’s manual. [. . . ]