User manual NAD C 356BEE

[. . . ] ® Owner’s Manual Stereo Integrated Amplifier C 356BEE РУССКИЙ SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ SAVE THESE INSTRUCTIONS FOR LATER USE. 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference. 3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. [. . . ] This output will be 12V when the C 356BEE is ON and 0V when the unit is either OFF or in standby. 3 IR IN/OUT: These mini-jacks accept and output remote-controlled codes in electrical format, using industry-standard protocols, for use with “IR-repeater” and multi-room systems and related technologies. IR IN: This input is connected to the output of an IR (infrared) repeater (Xantech or similar) or the IR output of another component to allow control of the C 356BEE from a remote location. IR OUT: When connected to the IR IN of an ancillary equipment, direct the ancillary equipment’s own remote control to the C 356BEE’s infrared receiver to command or control the linked unit. All NAD products with IR IN/IR OUT features are fully compatible with the C 356BEE. For non-NAD models, please check with your other product’s service specialists with respect to its compatibility with the C 356BEE’s IR features. 4 MP INPUT: Input for a Media Player or other line-level signal source. Use a twin RCA-to-RCA lead to connect these sockets to the left and right analog output of a Media Player. NOTE If an external Media Player is connected to the front MP socket (using a 3. 5mm stereo plug) while listening to a MP line-level source, the external Media Player will be directly selected with the MP line-level source immediately disconnected. Use a twin RCA-to-RCA lead to connect these sockets to the left and right analog output of a CD player. Use a twin RCA-to-RCA lead to connect these sockets to the left and right analog output of a tuner. 7 DISC INPUT: Input for additional line level input signals such as CD, Mini Disc player or the output signal from a step-up amplifier for a turntable. Use a twin RCA-to-RCA lead to connect these sockets to the left and right analog output of the auxiliary device. NOTE If an optional Modular Design Construction (MDC) module is installed, the DISC input socket is disabled and the MDC source is selected as the active input. 8 AUX INPUT: Input for additional line level input signals such as another CD player. Use a twin RCA-to-RCA lead to connect these sockets to the left and right analog output of the auxiliary device. 8 IDENTIFICATION OF CONTROLS REAR PANEL 9 TAPE 2 IN/OUT: Connections for analog recording and playback to a tape recorder of any type. Using twin RCA-to-RCA leads, connect the left and right “Audio Output” of the tape recorder to the TAPE 2 IN sockets for playback. Connect the left and right “Audio Input” of the tape recorder to the TAPE 2 OUT sockets for recording. 10 TAPE MONITOR IN/OUT: Connections for analog recording and playback to a secondary tape recorder of any type. Using twin RCA-to-RCA leads, connect the left and right “Audio Output” of the tape recorder to the TAPE MONITOR IN sockets for playback and tape monitoring. Connect the left and right “Audio Input” of the tape recorder to the TAPE MONITOR OUT sockets for recording. TO MAKE A RECORDING When any source is selected, its signal is also fed directly to any tape recorder connected to the TAPE 2 OUT or TAPE MONITOR OUT for recording. [. . . ] TABLE OF LIBRARY CODES APPLICABLE TO SR 8 REMOTE CONTROL LIBRARY CODE 10 11 20 21 22 23 30 31 40 41 42 NAD PRODUCT DESCRIPTION Default library for “AMP” page Zone 2 Default library for “CD” page; C 515BEE, C 545BEE, C 565BEE T 535, T 585, M55, DVD section of L 54, VISO TWO, VISO FIVE T 513, T 514, T 515, T 517 T 587, T 557, T 577, M56 IPD 1 IPD 2 Default library for “TUN” page; Tuner section of C 725BEE, T 175, T 737, T 747, T 755, T 765, T 775, T 785 C 422, C 425 C 445 13 РУССКИЙ SVENSKA NOTE The SR 8 may not necessarily contain all the control buttons applicable for the above-mentioned NAD products. Use the prescribed remote control of the specific NAD product for a full compliment of the applicable remote control buttons. NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH REFERENCE TROUBLESHOOTING ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ CONDITION No sound. POSSIBLE CAUSES • Mains power cord unplugged or power not switched ON. No audio despite the presence of an active input at DISC rear panel input terminals. [. . . ]