User manual MURATEC M-850

[. . . ] · Select the document type and the contrast. 4 Enter the number of copies using the numeric keypad. 5 Press START. $ Sort copy 1 Press COPY/FAX to change to Copy mode. Sort: 1 2 3 1 2 3 1 2 3 1 2 3 Non-sort: 1 2 3 1 1 1 2 2 2 3 3 3 2 Press SORT to turn the sort setting to on or off. When the sort setting is On, the LED on SORT glows. 3 Set the document in the ADF face up. Adjust resolution and contrast, if necessary. 4 Enter the number of copies using the numeric keypad. Helpful Tip The sort setting is set to On for the default setting. Press ENTER to save the setting. If you selected non-sort copies, you can use the FBS glass. 5 Press START. % Enlarged/Reduced copy 3 Fixed ratio If you want enlarged copies, use the FBS glass. 1 Set the document in the ADF or on the FBS glass. Adjust the document type and the contrast, if necessary. 1. Choose the desired ratio by using or of the cursor key. 2 Enter the document size by pressing the DOCUMENT SIZE. You can choose from: · 50% · 64% (Letter -> Half-letter) · 78% (Legal -> Letter) · 129% (Half-letter -> Letter) · 200% Helpful Tip If you want to reduce or enlarge your document automatically to fit on the paper size you selected, program the following setting in advance: 1. Adjust the ratio by 1 percent increments using or of the cursor key. You can set the ratio between 50% and 200%. Direct 4 Enter the number of copies using the numeric keypad. 1. [. . . ] Press # again. 5 Press START. ' Using the Bypass tray 1 Press COPY/FAX to change to Copy mode. 2 Set the document in the ADF face up, or on the FBS glass face down. 3 Open the bypass tray on the right side of your machine. Hopper 4 Place the paper on the bypass tray face down. Flapper release lever Pull out the hopper of the bypass tray and pull the flapper release lever. Adjust the paper guide to fit the paper. Then push back the flapper release lever. 5 The LCD will show the default paper size for the bypass tray. If you want to change it, proceed to step 6. Otherwise, skip to step 8. Helpful Tip If you want to change the default paper size for the bypass tray: 1. Press ENTER to save the setting. 6 Press BYPASS to change the paper size. The LCD will show: Set Bypass Ppr:Ltr / /Enter 8 Enter the number of copies. 9 Press START. Press or until your desired recording paper size appears. If you select "Other", press . When you use transparency film, select "Other", then "OHP". 7 Press ENTER. Just in case 1 Document Jam Contstor Enter/Cancl Clearing original document jams In this step, if more than 60 seconds passes without pressing any keys, the machine will begin to send or copy the document(s) stored during this operation. 2 Reset the document from the jammed page and press START. If you see this message on the LCD and wish to continue scanning from the jammed page, press ENTER. To abort the operation, press CANCEL. Open&Close ScanCover Reset Document In this step, if more than 60 seconds passes without pressing any keys, the machine will erase from memory all pages stored during this operation and the machine will return to the standby mode. If you see this message on the LCD, start the job again from the beginning. The check message "Repeat transmission. " will be printed out if the document jammed during transmission. This message will appear when the document jammed in the following cases: · The first page of the document jammed. · During the real time transmission or quick memory transmission. To remove the document . Remove the original document. If you cannot remove it, go to step 2. Otherwise, skip to step 3. 3 Gently close the scanner cover. Make sure both sides are snapped down securely. If the document has become wrinkled or torn, do not re-send it. ! Clearing printout jams 3 Important ! Be careful not to put your hand between the top cover and the machine. Important ! Shield the drum cartridge from light, especially strong light. Remove the toner and drum cartridge. 1 Pull up the top cover release and open the top cover. 2 Slide the printer cover release and open the printer cover. " Important ! The fuser unit becomes very hot. · Reduction rate · Reduction margin · Half-page reception Number of rings before your machine answers. Set the ring pattern to use with phone company's Distinctive Ring service. · Primary document type · Primary contrast mode You can set the margin for copying. Set the default setting to "Auto" for one of the following: · Paper size · Reduce/Enlarge ratio · Document size On/Off setting for Copy protection. On/Off setting to combine. Default setting Normal Normal Auto 40 mm Off Two times Two times One minute Two times On On On On Off Off Off -- Off Off Text Normal 24 mm 3 minutes Paper size Off On Off Off Page 4. 1 4. 3 4. 4 4. 5 4. 5 4. 2 4. 2 4. 2 4. 1 3. 53 3. 49 3. 51 3. 15 4. 4 3. 23 4. 6 4. 6 4. 7 4. 7 2. 18 4. 7 2. 17, 4. 7 2. 17, 4. 8 3. Copy Settings 02. Print parameter 03. Auto Reset Time 04. Copy Auto 05. Copy Protect 06. Sort Copy 07. Nega/Posi 08. Combine (for MFX-1700 only) 17 Level one function B. User Settings Level two function 4. Printer Settings 5. Scanner Settings*4 C. Other Settings 1. Journal & Reports Level three function 01. TCP/IP*3 01. Scan Parameter 02. Scan Size 03. Auto Reset 01. Journal Auto Print 02. Journal Line Up 03. Report AutoPrint 01. Set Cover Page 02. Enter Cover Page 01. Set Dept. Setting 04. Erase Dp. TimeList 01. Set F-Code Box 02. Erase F-Code Box 01. Set Batch Box 02. Erase Batch Box 01. Polling Document 02. F-Code Document 01. Polling Document 02. F-Code Document 03. Batch Document 01. Polling Document 02. F-Code Document 03. Batch Document 04. Security Rx Doc. 2. Cover Page 3. Department Code 4. F-Code Box 5. Batch Tx D. Management 1. Store Document 2. Erase Document 3. Document Print 05. Com. [. . . ] Management 1. Store Document 2. Erase Document 3. Document Print 05. Com. Stored Doc. Summary of setting Enter the IP Address, Subnet mask and Gate way address. User Install Summary of setting Print a list of your machine settings. Print a total communication time and printed pages of each department code. [. . . ]