User manual MURATEC M-820

[. . . ] l ih As an Energy Strfi partner, Muratec America, Inc. , has determined a that this product meets the Energy St guidelines for energy effar i ciency. Energy saving Your machine can save the energy with its Energy Saving Mode. In the Energy Saving Mode the printer will not use its fusing lamp and Energy Save Mode will be displayed on the LCD. If your machine receives a fax message or if any key is pressed your machine will automatically wake up. The time for the machine to enter the Energy saving mode can be selected from 1 to 240 minutes. [. . . ] ni Type :Communication / /Enter 3. 39 Advanced features 6 Press ENTER. The LCD now shows either: P2:Fax#/Advan. Func. _ o 9-5558743_ r Programming an F-Code transmission P2:Fax#/Advan. Func. For this operation to work, two things must be true: You must know how the remote fax is using each F-Code box to which you re transmitting for example, as a security box or a relay box. Different fax manufacturers may use slightly different terms, but the concepts are the same. You must know the remote fax s ITU- sub-address and password for each box to T which you want to transmit. To program an F-Code transmission into a programmable one-touch key: Press Program key, 1 ble one-touch number A, 3, 0, 1, ENTER. The LCD shows the first empty programmaavailable: the numeric keypad to 7 Use including whatever codesenter the number exactly as your machine should dial it, your phone system requires. The number can be up to 40 characters in length: P2:Fax#/Advan. Func. To view characters beyond those 20, press t s r l t t e l fto o col o h e r t srl t tergt o col o h ih. P2:No Number Stored Note: I P2 appears on the LCD, it means that you have already entered a numf b r f r P1. You can see what you programmed into P1 by pressing , f eo i you want. For example, if you set P1 for storing of the polling document, you will see: while you 8 Next, twice and can still see the fax number on the LCD, press A D VA N C E D F U N CTIONS then press ENTER. want the 9 If you and skip polling to begin immediately every time you press the key, press ENTER to step 12. If you want to delay the polling, press A D VA N C E D FUNCTIONS, ENTER. 10 Next, tell your fax to carry out this delayed command one of these ways: Option 1: Perform the command once at a certain time on a certain day of the month. To program an F-Code polling operating into a programmable one-touch key: Press Program key, 1 ble one-touch number A, 3, 0, 1, ENTER. The LCD shows the first empty programmaavailable: Contrast :------/ /Enter 19 20 Press until the mode you want appears. Press ENTER. The LCD asks if you want the memory transmission on or off when using this programmable one-touch number. Memory Tx :--/ /Enter Select Program No. P2:No Number Stored Note: I P2 appears on the LCD, it means that you have already entered a numf b r f r P1. You can see what you programmed into P1 by pressing , f eo i you want. For example, if you set P1 for storing of the polling document, you will see: 21 22 Press until the mode you want appears. Press ENTER. The LCD asks you for the type of confirmation report you want to set for this programmable one-touch number. Report :--/ /Enter Select Program No. P1:Polling Document Press to go back to the programmable one-touch key you want to enter. Note: To erase a programmable one-touch key, see page 3. 48. 23 24 Press until the mode you want appears. Press ENTER. The LCD asks if you want to send a cover page for this programmable one-touch number. Cover Page :--/ /Enter 2 Press the key that you want to program or change. P2:No Number Stored Note: If your previous command for this key was for an F-Code polling operation and you want to keep this key programmed for an F-Code polling operation, use these instructions to make changes. But if you want to assign this key to a completely different operation (for a delayed transmission, for example), then you first must erase the stored command before programming the new one. one-touch key than the one that appears on the LCD, Press ENTER. The LCD 4 grammable one-touch:asks which operation you want to program into the pro- 25 26 Press until the mode you want appears. Press ENTER. The LCD asks if you want to turn the Fax & Copy feature on or offfr o this programmable one-touch number. Fax & Copy :--/ /Enter LCD Note: When the memory transmission is set to off in step 20, this appear and go to step 29. wl nt il o 27 28 29 3. 42 Press Press Press until the mode you want appears. ENTER. STO P to return your machine to standby mode. Type :Communication / /Enter Advanced features Note: If changing a previously stored command, skip to step 7. 5 Press utl Communication appears. ni 12 13 Type :Communication / /Enter If you want the transmission to begin immediately every time you press the key, press ENTER and skip to step15. If you want to delay the transmission, press A D VA N C E D FUNCTIONS, ENTER. [. . . ] 1. 9 Appendix and index Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 3 Sorting copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 13 Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 16 Activity journal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]