User manual MURATEC F-85

[. . . ] . Ferrite core NOTE: The inclusion of the AC power cord and telephone line cable vary according to countries. Save the carton and packing material in case there's a need for reshipment. 2 Installation Manual Step 3 : Setup the machine Remove all the shipping materials MFX-2030 and MFX-1430: Open the ADF cover, then remove the protective sheet from the ADF. Remove the protective sheet between the platen cover and document glass. (MFX-2030, MFX-1430 only) Open the cassette and remove the spacer in the paper cassette. Remove the protective sheet covering the touch panel. F-560 and F-520: Open the ADF cover, then remove the protective sheet from the ADF. Open the cassette and remove the spacer in the paper cassette. [. . . ] Remove the protective sheet covering the touch panel. F-560 and F-520: Open the ADF cover, then remove the protective sheet from the ADF. Open the cassette and remove the spacer in the paper cassette. Remove the protective sheet covering the touch panel. Installation Manual 3 Attach the document tray Attach the document tray by inserting it into the appropriate holes, as shown below. Unlock the scanner (For MFX-2030, MFX-1430 only) IMPORTANT: In order to avoid damaging the unit, the machines scanner is locked prior to shipping. If you need to relocate the machine, lock the scanner prior to moving it. To lock the scanner, please use the reverse process of the instructions below. 1 Slide the scanner locking knob to the back until it clicks in the unlocking position. 2 Turn off the transport mode (see Step 8 "Turn off the transport mode, " page 12). 4 Installation Manual Step 4 : Install the consumables 1 Pull the release lever to open the side cover. 2 Open the front cover. 3 Turn the toner cartridge locking lever to the left (unlock position). 4 Unpack the drum cartridge from its carton and slide it into the machine firmly until it locks into place. NOTE: DO NOT touch the drum surface. Installation Manual 5 5 Unpack the starter toner cartridge, hold it with both hands and gently shake it to distribute the toner evenly inside the cartridge. NOTE: Do not touch the roller of the toner cartridge. 6 Slide the toner cartridge into the machine firmly until it locks into place. Then turn the cartridge locking lever to the right until it locks into place. 7 Close the front and side covers. 6 Installation Manual Step 5 : Load paper into the cassette Acceptable paper sizes for the cassette: Region U. S. European and Asian countries Paper size Letter, Legal, Half-letter A4, A5 , F4 Paper type Plain paper Quantity 500 sheets (Weight: 20­24 lbs. 60­90g/m2) 60g/m2) 1 Pull the handle toward you to open the paper cassette. 2 Press the paper lifting plate down until it locks into position. 3 Adjust the rear paper guide to the desired paper length. Installation Manual 7 4 Load the paper into the cassette. · Make sure you properly stack the paper prior to setting it in the cassette. The leading edge and sides should be even. · Do not stack the paper over the limit mark inside the cassette. 5 Pinch the side paper guide and adjust it to the width of the paper. 6 7 8 9 Close the paper cassette. Attach the appropriate paper size sticker to the front of the cassette. Line" settings are not appear according to the country. 14 Installation Manual Step 10 : Set the paper size 1 Press [Setting] on the control panel, then [Paper Settings]. 2 Press [Cassette 1]. 3 Select the paper that you loaded, and press [Enter]. U. S. European and Asian countries NOTE: Selectable paper varies by countries. 4 If the optional second paper cassette has been installed, set the paper size following these steps. Installation Manual 15 Step 11 : Assigning an IP Address If your network is using DHCP If a DHCP (Dynamic Host Configuration Protocol) server is installed on your network, an IP address is automatically assigned after you connect the machine to the network. 1 2 To see the assigned IP address for your machine, print the "Network setting list". by pressing [Setting] [List] [Network Settings] [Yes] on the control panel. Go to "Verifying the IP settings" on page 19 and begin with step 2. NOTE: Once the DHCP server has assigned the IP address to your machine, that IP address MUST be reserved within the specific DHCP scope. Failure to do so could result in failed operation when the IP address lease expires. If your network is not using DHCP You should turn off the DHCP server setting. Then enter the IP address manually to install your machine on your network. 1 Press [Setting] on the control panel, then [Management]. 2 Press [Network Settings]. 16 Installation Manual 3 Press [TCP/IP Settings]. 4 Press [DHCP Setting]. 5 Select [OFF] and press [Enter]. NOTE: If you are not installing the machine on a network, please skip to step 14 "Local print and scan driver installation" on page 23. Installation Manual 17 6 Press [IP Address]. 7 Enter the appropriate IP address using the numeric keys. Press [Subnet Mask] and enter the appropriate IP address, then press [Enter]. Refer to the above steps on how to enter the IP address. 10 If necessary, enter the gateway address. 11 When you are finished, reboot the machine to activate the new settings. (Turn the machine off and after three or more seconds, turn it on. ) 12 Go to "Verifying the IP settings" on next page. 18 Installation Manual Verifying the IP settings 1 2 Print the network setting list to view the new configuration. To print the network settings list: Press [Settings], [List], [Network Settings], then [Yes] At the command prompt on a network computer, type "ping" followed by the IP address of your machine. (Sample) NOTE: To run the command prompt: On Windows 98 Click Start Programs MS-DOS Prompt On Windows Me Click Start Programs Accessories MS-DOS Prompt On Windows 2000 and XP Click Start ALL Programs Accessories Command Prompt On Windows NT 4. 0 Click Start Programs Command Prompt On Windows server 2003 Click Start Command Prompt Installation Manual 19 Step 12: Browser-based setup Your machine can be set up from a browser. [. . . ] To print the network settings list: Press [Settings], [List], [Network Settings], then [Yes] At the command prompt on a network computer, type "ping" followed by the IP address of your machine. (Sample) NOTE: To run the command prompt: On Windows 98 Click Start Programs MS-DOS Prompt On Windows Me Click Start Programs Accessories MS-DOS Prompt On Windows 2000 and XP Click Start ALL Programs Accessories Command Prompt On Windows NT 4. 0 Click Start Programs Command Prompt On Windows server 2003 Click Start Command Prompt Installation Manual 19 Step 12: Browser-based setup Your machine can be set up from a browser. To access the machine's web page: 1 2 Type the machine's IP address in the URL address field of your browser. http://192. 168. 1. 10/) The start-up web page will appear. NOTE: Please refer to the "Network Guide" chapter 5 "Using the web browser to change the settings" for more information. 20 Installation Manual Step 13: Setup e-mail server In order to use the e-mail and Internet fax function on your machine, the "SMTP/POP" settings and "E-mail Settings" must be setup. [. . . ]