User manual MULLER MARTINI CONTROL CONSOLE 2500

[. . . ] Müller Martini Druckmaschinen GmbH Operating Manual Control Console 2500 Serial Number Article Number of Operating Manual 2500. 4002. 71 Alprinta 52/74 Control Console Table of Contents 2500 1 1. 1 Introduction 1-1 3 Control Console of Alprinta . . 2 2. 1 2. 1. 1 2. 1. 2 2. 1. 3 2. 2 2. 2. 1 2. 2. 2 2. 3 2. 3. 1 2. 3. 2 2. 4 2. 4. 1 2. 5 2. 5. 1 2. 6 2. 6. 1 2. 6. 2 2. 6. 3 2. 6. 4 Safety Guidelines 2-1 3 3 3 4 4 4 4 5 5 5 6 6 6 6 7 7 7 9 10 General . . 3 3. 1 3. 2 3. 2. 1 3. 2. 2 3. 3 3. 4 Introduction to Visualization 3-1 3 7 7 9 10 30 Glossary of Terms . . 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 0-1 Control Console Table of Contents Alprinta 52/74 2500 3. 4. 1 3. 4. 2 3. 4. 3 3. 5 3. 5. 1 3. 5. 2 3. 5. 3 3. 5. 4 Dialog Boxes . [. . . ] Register Card Circulation Counter In the register card Circulation Counter print run. you can make various settings for the total 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 6-7 Control Console Counter Use during Production Alprinta 52/74 2500 With this function you can: Preset value Enter the total value of the run in number of copies into a numerical entry field (see chapter 3. 5. 2 , , Entry of Numerical Value", page 3-41). Counting direction ascending descending By touch select the counting direction of the counter until the set value of the total run is reached. The ascending count goes from zero (0) to the set value and descending count goes from set value to zero (0). After the counter is turned on this is shown as ascending or descending number of copies in the actual value field and by a bar with progress indication in the start screen. If the counter is turned on this setting is active immediately, without confirmation of the dialog box with . 6-8 2500. 4002. 71 Müller Martini Druckmaschinen GmbH 02. 2009 Alprinta 52/74 Control Console Counter Use during Production 2500 End stop stop at the end active stop at the end not active Determine if the machine should stop after reaching the total run or not. You have a choice between stop at the end active and stop at the end not active. This setting is displayed by superimposing or dimming out of in the counter field next to the bar with progress display in the upper left in the machine screen. A respective warning will indicate when the set value of the total run is reached and/or setting of the end stop: total run complete and end stop selected when end stop is activated or total run complete when end stop deactivated. Counter-Reset Reset the counter of the total run immediately, e. g. During the ascending count the counter is set to zero and with descending count to set value. This setting is immediately active when the counter is on, without confirmation of the dialog box with . Actual value Display the actually achieved number of printed products in the total run. This value changes continuously based on the counting direction set until the set value entered for the total run has been reached. 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 6-9 Control Console Counter Use during Production Alprinta 52/74 2500 The mentioned setting values of the total run can be entered before the counter is turned on. The effective count of printed products begins only after switching on the counter with the Hotkey button . If the machine is stopped when the counter is turned on the numerical display of the batch as well as the progress display of the total run remains at the actual value reached. With an activated end stop the machine stops after the total run is complete. Afterward the counter is reset with Reset, the machine is started again and the counter turned on with . With a deactivated end stop the machine does not stop after the total run is complete. The warning total run complete is displayed and the counter must be reset manually with Reset. After confirmation of the dialog box Counter and confirming the indication with the warning window is dimmed out. With every counter reset the bar with the progress display in the Production screen is either dimmed out or build up again, depending on the direction of counting. The display in the counter field of the Production screen is only updated after confirming the dialog box Counter with . 6 - 10 2500. 4002. 71 Müller Martini Druckmaschinen GmbH 02. 2009 Alprinta 52/74 Control Console Counter Use during Production 2500 B. Register Card Batch Counter In the register card Batch Counter run(s). you can make different settings for the batch A total run can be divided into several batches based on the intended finishing. 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 6 - 11 Control Console Counter Use during Production Alprinta 52/74 2500 With this function you can: Reference value Enter the total value of the batch in number of copies into a numerical entry field (see chapter 3. 5. 2 , , Entry of Numerical Value", page 3-41). Counting direction Up Down Select the counting direction of the counter to the set value of the batch by simple touch. [. . . ] on the background visualization). Never change the measuring parameters in the "Expresso Pro" window! 12 - 20 2500. 4002. 71 Müller Martini Druckmaschinen GmbH 02. 2009 Alprinta 52/74 Control Console Index 2500 13 Index Numerics 5 m/min CRAWL SPEED . 4-4 11 - 3 4 - 21 5 - 35 7 - 13 5 - 37 11 - 5 6 - 10 4 - 22 13 - 13 5 - 47 5 - 50 4 - 18 5 - 34 11 5 11 9 9 . . . . B BASIC CONFIGURATION SERVICE LEVEL BASIC CONFIGURATION USER LEVEL . 11 - 18 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 13 - 1 Control Console Index Alprinta 52/74 2500 Cancel an entry . [. . . ]