User manual MTD TB75SS 41DDT75C063

[. . . ] Operator’s Manual 2-Cycle Gasoline Trimmers Model TB75SS or TB25CS IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY P/N 769-00734 (4/03) PRINTED IN USA INTRODUCTION THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. This operator’s manual provides you with easy-tounderstand operating instructions. Read the whole manual and follow all the instructions to keep your new outdoor power tool in top operating condition. [. . . ] € Slowly move the trimmer into and out of the cutting area at the desired height. € The life of your cutting line is dependent upon: • Following the trimming techniques • What vegetation is being cut • Where vegetation is cut For example, the line will wear faster when trimming against a foundation wall as opposed to trimming around a tree. 12 ADJUSTING TRIMMING LINE LENGTH The Bump Head™ cutting attachment allows you to release trimming line without stopping the engine. To release more line, lightly tap the cutting attachment on the ground (Fig. Line release becomes more difficult when the cutting line gets shorter. tB75SS TB25CS DECORATIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around trees , posts , fences and more. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground (Fig. A blade in the cutting attachment shield will cut the line to the proper length if any excess line is released. Line release becomes more difficult when the cutting line gets shorter. 14 TB25CS 11 MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to any non-road engine repair establishment, individual or authorized service dealer. WARNING: To prevent serious injury, never do maintenance or repairs with unit running. NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by any non-road engine repair establishment, individual or authorized service dealer. In order to assure peak performance of your engine, inspection of the engine exhaust port may be necessary after 50 hours of operation. If you notice lost RPM, poor performance or general lack of acceleration, this service may be required. If you feel your engine is in need of this inspection, refer service to any non-road engine repair establishment, individual or authorized service dealer for repair. DO NOT attempt to perform this process yourself as engine damage may result from contaminants involved in the cleaning process for the port. FREQUENCY Before starting engine Every 10 hours Every 25 hours MAINTENANCE REQUIRED Fill fuel tank with fresh fuel Clean and re-oil air filter Check and clean spark arrestor Check spark plug condition and gap Inspect exhaust port and spark arrestor screen for clogging or obstruction to assure maximum performance levels REFER TO Page 8 Page 15 Page 16 Page 18 Page 16 Every 50 hours LINE INSTALLATION FOR THE SPEEDSPOOL® WARNING: Never use metal-reinforced line, wire, chain, or rope, etc. Lines other than those specified may make the engine overheat or fail. There are two methods to replace the SpeedSpool® trimming line: • Wind the inner reel with new line • Install a pre-wound inner reel WARNING: Always use the correct line length when installing trimming line on the unit. Top View Of The SpeedSpool® Arrows Outer Spool Winding the Inner Reel With New Line NOTE: It Is unnecessary to remove the bump knob to install a new trimming line. [. . . ] € Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission related parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durability may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer • The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel pick up/ fuel filter, ignition module, spark plug and muffler. 21 MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. Troy-Bilt LLC warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. [. . . ]