User manual MTD 190-678

[. . . ] You will be asked to enter the serial number in order to process your call.   FastAttach™ Twin Bag Grass Collector This Model 190-678 Twin Bag Grass Collector is a grass collection system designed for use on all Cub Cadet 46” cut series 1000 lawn tractors. Carefully read all sections and study the illustrations to ensure proper installation and usage of this attachment. They are included to provide for the protection of the equipment installer and user, and to ensure the prolonged service life of the equipment. NOTE: References to LEFT and RIGHT indicate the left and right sides of the tractor when facing forward in the operator’s position. [. . . ] 3. Secure the blade spindle and turn the hex flange nut counterclockwise to loosen and remove the blade from the spindle assembly. One set has round spindle holes and the other set has star spindle holes. To determine which blades your unit utilizes, compare the blades removed with the blades included in your bagger kit. 5. After determining the appropriate blade set, mount the SMALLER of the three blades to the CENTER spindle. Be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the rider is in the operating position. 6. Use a torque wrench to tighten the blade spindle hex flange nut to between 70 and 90 foot-pounds. 7. Remount the cutting deck. Smaller Blade Larger Blades Hex Flange Nut Figure 5-1 NOTE: The hex flange nut has a normal (right-handed) thread pattern. NOTE: The retainer strap is factory installed at position A on the discharge chute. However, on older models of tractors, you will have to change the position of the strap depending on the location of the grass catcher pin on the deck. Remove the retainer strap from position A on the discharge chute and move to position B or C corresponding to the position of the grass catcher pin at B or C on the deck. See Figure 5-2. Figure 5-2 1. On older models: Some older model decks may have a retainer clip installed in the positon (near the discharge chute opening) that the new grass catcher pin must be installed. NOTE: Referring to Figure 5-4, the retainer strap is factory installed at position A on the discharge chute. This is the appropriate position for decks that have the grass catch pin installed at position A as shown in Figures 5-2 and 5-4. However, some older model decks may only allow installation of the grass catcher pin in either position B or C as shown in Figures 5-2 and 5-4. If the pin is installed in either positions B or C, remove the retainer strap and reinstall in the correct postion on the discharge chute as shown in Figure 5-4. NOTE: Some mower deck may have the grass catcher pin installed at the factory. If applicable, attach pin to the right/front of the deck at position A as Install Discharge Chute A Figure 5-3 B Figure 5-4  shown in Figures 5-2 and 5-4. If installing on an older deck that has no hole at position A, install the pin either where the retainer clip was removed, or at position B or C as applicable, and reposition the retainer strap on the discharge chute to the appropriate position. 4. Raise the chute deflector on the deck and hold it while you position the discharge chute over the deck discharge opening. 5. Place the top rear edge of the discharge chute over the top rear edge of the discharge opening. Retainer Strap Grass Catcher Pin Attaching Discharge Chute 5 Figure 5-5 6. Push down on the discharge chute so that its front bottom edge rolls around the bottom of the deck, then slide the chute forward until it completely covers the deck discharge opening. 7. Lock the discharge chute in position by hooking the retainer strap over the grass catcher pin on the deck. 8. Insert the curved end of chute tube into the hole in the grass bag cover. [. . . ] The terms of this warranty provide the sole and exclusive remedy arising from the sale and/or lease of the products covered hereby. Cub Cadet shall not be liable for any incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. [. . . ]