User manual MTD MS1635

[. . . ] ¤ ¤ USER MANUAL Gasoline Chain Saws MANUEL DE UTILISATION Tronçonneuses à essence MANUAL DEL USUARIO Sierras de Cadena de Gasolina STOP ARRÊT ALTO Models : MS1432, MS1435, MS1635, MS1635AV, MS1838AV, MacCat Super 16 AV For problems or questions, DO NOT return this product to the store. Box 361131 Cleveland, OH 44136-0019 Canada Imported by / Importé par: MTD PRODUCTS LIMITED 97 Kent Avenue Kitchener, ON CANADA N2G 4J1 For Consumer Assistance Please Call L'Aide Du Consommateur Necessitez S'il Vous Plait Para La Ayuda Del Consumidor Llame Por Favor This product has been tested at a computed kickback angle (CKA) of no greater than 23. For your own safety, please read and follow the safety precautions in this manual before attempting to operate your chain saw. With proper operation and maintenance, it will provide you with years of service. [. . . ] If 2-cycle lubricant other than McCulloch Custom Lubricant is to be used, it must be a premium grade oil for 2-cycle air cooled engines mixed at a 40:1 ratio. Do not use any 2-cycle oil product with a recommended mixing ratio of 100:1. If insufficient lubrication is the cause of engine damage, it voids the manufacturer’s engine warranty for that occurrence. MIXING FUEL Mix fuel with McCulloch brand 2 cycle oil in an approved container. WARNING To Test CHAIN BRAKE®: ® The purpose of the CHAIN BRAKE® is to reduce the possibility of injury due to kickback; however, it cannot provide the intended measure of protection if the saw is operated carelessly. Always test the CHAIN BRAKE® before using your saw and periodically while on the job. The CHAIN BRAKE is DISENGAGED (chain can move) when BRAKE LEVER IS PULLED BACK AND LOCKED (Figure 3-5A). The CHAIN BRAKE® is ENGAGED (chain is stopped) when brake lever is in forward position. If strong resistance is felt, or lever does not move into either position, do not use your saw. Take it immediately to a McCulloch Authorized Service Center for repair. RECOMMENDED FUELS H Some conventional gasolines are being blended with oxygenates such as alcohol or an ether compound to B meet clean air standards. Your McCulloch engine is designed to operate satisfactorily on any gasoline intended for automotive use including oxygenated gasolines. CHAIN AND BAR LUBRICATION Always refill the chain oil tank each time the fuel tank is refilled. We recommend using McCulloch Chain, Bar and Sprocket Oil, which contains additives to reduce friction and wear and to assist in the prevention of pitch formation on the bar and chain. ENGINE PRE-START CHECKS E N Never start or operate the saw unless the bar and chain are properly installed. Be certain the CHAIN BRAKE® is disengaged (C) before starting unit (Figure 5-1A). RECOMMENDED FUELS H Some conventional gasolines are being blended with oxygenates such as alcohol or an ether compound to B meet clean air standards. Your McCulloch engine is designed to operate satisfactorily on any gasoline intended for automotive use including oxygenated gasolines. CHAIN AND BAR LUBRICATION Always refill the chain oil tank each time the fuel tank is refilled. We recommend using McCulloch Chain, Bar and Sprocket Oil, which contains additives to reduce friction and wear and to assist in the prevention of pitch formation on the bar and chain. ENGINE PRE-START CHECKS E N Never start or operate the saw unless the bar and chain are properly installed. Be certain the CHAIN BRAKE® is disengaged (C) before starting unit (Figure 5-1A). [. . . ] This is normal during the break-in period, and the interval between future adjustments will begin to lengthen quickly. WARNING E N G L I S H GUIDE BAR MAINTENANCE: Most guide bar problems can be prevented merely by keeping the chain saw well maintained. Insufficient guide bar lubrication and operating the saw with chain that is TOO TIGHT will contribute to rapid bar wear. BAR AND CHAIN REPLACEMENT COMBINATIONS: E N G Never have more than 3 links removed from a loop of chain. [. . . ]